DO NOT
SCALE FROM
THIS PRINT
(SEE TABLE 1)
"A" REF
.100 2.54
REF
.300 7.62
REF
(SEE TABLE 1)
"C" REF
.020 0.51
REF
.178
4.51
REF
.0787 2.000
"B"
-
.004
+
.006
(SEE TABLE 1)
2
MAX SWAY
(EITHER DIRECTION)
"A"
"A"
01
02
C
C
L
C
L
C
C
.370 9.40
REF
.020
SQ REF (TYP)
0.50
.593 15.07
REF
SECTION "A"-"A"
SCALE 2.5 : 1
EHH-XX-D-SR
LC-09-TM
EHA-06
C
.093
REF
2.35
(SEE TABLE 1)
"E" REF
(SEE TABLE 1)
"D"
T-1S13-05-XXX-2
.005 0.12
(SEE NOTE 7)
.060 1.52
90°
.120 3.05
REF
C
C
.004[0.10]
POS 1 INDICATOR
No OF POSITIONS
-05 THRU -25
LEAD STYLE
PLATING SPECIFICATION
-S: 30µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL.
-F: 3µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL.
-T: 200µ" MATTE TIN ON ENTIRE CONTACT.
-H: 30µ" SELECTIVE GOLD IN CONTACT
AREA, 3µ" SELECTIVE GOLD ON TAIL.
-L: 15µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL.
TAIL OPTION
POLARIZATION OPTION
ROW SPECIFICATION
OPTION 1
OPTION 2
OPTION 3
EHT-1XX-01-X-D-XX-SR-XX-XX-X-XX
-SR STRAIN RELIEF
-P: PICK & PLACE PAD
(FOR -SM ONLY, USE PPP-24)
(USE PPP-55 WITH -SM-TR OPTION)
(SEE SHT 3, FIG 5)
(NOT AVAILABLE WITH -LC)
-K: POLYIMIDE FILM PAD
(SEE SHT 2, FIG 4)
(NOT AVAILABLE WITH -LC)
(FOR -SM ONLY)
-RA: RIGHT ANGLE
-SM: SURFACE MOUNT
(LEAVE BLANK FOR THRU HOLE)
-LC: LOCKING CLIP(SEE NOTE 8)
(FOR -SM ONLY, SEE NOTE 8)
(NOT AVAILABLE WITH -P OR -K)
-XX= PIN OMITTED
-TR: TAPE & REEL
-01
-D: DOUBLE
C
FIG 1
(EHT-105-01-XX-D-SM-SR-LC SHOWN)
C
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [0.3] 2
.XXX:
.005 [0.13]
.XXXX:
.0020 [0.051]
MATERIAL:
EHT EJECTOR HEADER ASSEMBLY
BY:
EHT-1XX-01-X-D-XX-SR-XX-XX-X-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
CHADP
08/04/2008
3
1
SHEET SCALE: 5:2
c:\enterprisevault\DWG\MISC\MKTG\EHT-1XX-01-X-D-XX-SR-XX-XX-X-XX-MKT.SLDDRW
MAX FLASH ALLOWED: .002[0.05]
MAX GATE VESTIGE: .002[0.05]
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY TO BE WITHIN .004[0.10].
3. BURR ALLOWANCE: .0015[0.038] MAX.
4. MINIMUM PUSHOUT FORCE: .5 LB. [2.22N]
5. MAXIMUM ALLOWABLE BOW: .002[0.05]
INCH/INCH AFTER ASSEMBLY.
6. MAXIMUM PIN ROTATION IN BODY: 2°
7. MEASURE AT BEND
8.DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED,
THE –LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT.
SAMTEC RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE –LC OPTION.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
INSULATOR: VECTRA E130, COLOR: NATURAL
TERMINAL: PHOS BRONZE
REVISION H
