60
112116
TLC Series
Tantalum Solid Electrolytic Chip Capacitors
Consumer Series
RATINGS & PART NUMBER REFERENCE
Rated Rated Category Category DCL
ESR
100kHz RMS Current (mA)
AVX Case Capacitance
Voltage Temperature Voltage Temperature Max.
Max.
MSL
Part No. Size (μF)
(V) (ºC) (V) (ºC) (μA)
@ 100kHz
25ºC 85ºC 125ºC
(Ω)
20 Volt @ 40°C
TLCH225M020#TA H 2.2 20 40 4 125 0.5 7.5 3 89 80 36
TLCR106M020#TA R 10 20 40 4 125 0.6 5 3 95 85 38
25 Volt @ 40°C
TLCL105M025#TA L 1.0 25 40 5 125 0.5 7.5 3 58 85 23
TLCR225M025#TA R 2.2 25 40 5 125 0.6 5 3 95 85 38
35 Volt @ 40°C
TLCR105M035#TA R 1.0 35 40 7 125 0.5 5 3 95 85 38
**Please contact manufacturer, availability upon request
Moisture Sensitivity Level (MSL) is defined according to J-STD-020.
All technical data relates to an ambient temperature of +25°C. Capacitance and DF are measured at 120Hz, 0.5V RMS with a maximum DC bias of 2.2 volts.
DCL is measured at rated voltage after 5 minutes.
DCL allowed to move up to 2.00 times the limit post mounting.
For typical weight and composition see page 223.
NOTE: AVX reserves the right to supply a higher voltage rating or tighter tolerance part in the same case size, to the same reliability standards.
QUALIFICATION TABLE
TEST
TLC series (Temperature range -55ºC to +125ºC)
Condition Characteristics
Visual examination
no visible damage
Endurance
DCL 1.25 x initial limit
ΔC/C within ±30% of initial value
ESR 1.5 x initial limit
Visual examination
no visible damage
Humidity
DCL 2 x initial limit
ΔC/C ±30% of initial value
ESR 1.25 x initial limit
+20ºC -55ºC +20ºC +40ºC +60ºC +85ºC +125ºC +20ºC
Temperature
DCL
IL* n/a IL* 1.25 x IL* 1.25 x IL* 1.25 x IL* 1.25 x IL* IL*
Stability
ΔC/C
n/a +0/-25% ±5% +10/-0% +10/-0% +20/-0% +25/-0%
+20/-10%
ESR
IL* n/a 1.25 x IL* 1.25 x IL* 1.25 x IL* 1.25 x IL* 1.25 x IL* 1.25 x IL*
Visual examination
no visible damage
Surge
DCL 2 x initial limit
Voltage
ΔC/C within ±30% of initial value
ESR 1.25 x initial limit
Determine after application of rated voltage for 2000
+48/-0 hours at 40±2ºC and then leaving 1-2 hours at
room temperature. Also determine of 85ºC tempera-
ture, category voltage for 2000 +48/-0 hours and
then leaving 1-2 hours at room temperature. Power
supply impedance to be ≤0.1Ω/V.
Determine after storage without applied voltage
at 40±2ºC and 90-95% relative humidity for 56
days and then recovery 1-2 hours at room
temperature.
Test temperature: 40ºC+3/0ºC
Test voltage: 1.3 x rated voltage
Series protection resistance 1000±100Ω
Discharge resistance: 1000Ω
Number of cycles: 1000x
Cycle duration: 6 min; 30 sec charge,
5 min 30 sec discharge
Step Temperature°C Duration (min) Voltage Applied
1 +20±2 15 N/A
2 -55+0/-3 15 N/A
3 +20±2 15 N/A
4 +40+2/-0 15 V
R
5 +60+2/-0 15 0.66 x V
R
6 +85+3/-0 15 0.50 x V
R
7 +125+3/-0 15 0.20 x V
R
8 +20±2 15 N/A
*Initial Limit
