SERIES
MATERIAL NUMBER
CUSTOMER
GENERAL MARKET
171813
SEE CHART
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NUMBER
1 OF *
DIMENSION UNITS SCALE
MM/IN
4:1
DRWN BY DATE
MKIPPER
2012/09/13
CHK'D BY
DATE
SSOUSEK
2012/09/13
APPR BY DATE
FSMITH
2013/06/11
DOCUMENT NUMBER
DOC TYPE
DOC PART
SD-171813-0001 PSD
000
DRAWING SIZE
THIRD ANGLE PROJECTION
C
KK RPC 156 FRICTION LOCK
VERTICAL HEADER ASSEMBLY SOLID BODY W/O
PEGS
PRODUCT CUSTOMER DRAWING
ADD NOTE 12
2017/02/03
2017/02/06
2017/02/09
113073
BAPPELDORN
JBELL
FSMITH
EC NO:
DRWN:
CHK'D:
APPR:
B1
REV
GENERAL TOLERANCES
(UNLESS SPECIFIED)
MM
INCH
4 PLACES
± ±
3 PLACES
± ±
0.01
2 PLACES
±
0.25
±
0.015
1 PLACES
±
0.38
±
0 PLACES
± ±
ANGULAR TOL
±
0.5
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
FORMAT: Eng-lega-master-tb-prod-C
REVISION: C
DATE: 2016/02/04
RELEASE STATUS RELEASE DATE
DETAIL Z
SCALE 8:1
-D-
-E-
OPTIONAL PICK AND PLACE CAP
FOR TAPE AND REEL PACKAGING
RECOMMENDED P.C.BOARD LAYOUT
NON-ACCUMULATIVE
NOTES:
1. MATERIAL: HOUSING: NYLON, UL94V-1, COLOR: BLACK
PINS: BRASS
2. FINISH:
(197-TIN) = OVERALL REFLOWED MATTE TIN: 0.00152/.000060 MIN.
OVER 0.00127/.000050 MIN. NICKEL OVERALL.
(208) = SELECT GOLD: 0.00038/.000015 MIN,
SELECT MATTE TIN: 0.00254/.000100 MIN,
BOTH OVER 0.00127/.000050 MIN NICKEL.
(228) = SELECT GOLD: 0.00076/.000030 MIN,
SELECT MATTE TIN: 0.00254/.000100 MIN,
BOTH OVER 0.00127/.000050 MIN NICKEL.
3. PRODUCT SPECIFICATION: PS-171813-0001, PS-171813-0002
4. PACKAGING INFORMATION: SEE CHARTS.
5. SOLDERABILITY: PER SMES-152.
6. PIN PUSH-OUT FORCE: PRIOR TO SOLDERING, A 3 LB. MINIMUM FORCE IN
EITHER DIRECTION
7. PARTS ARE STACKABLE END TO END ON 3.96/.156 CENTERS.
8. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC
SPECIFICATION PS-45499-002.
9. SLOTS ON BACKWALL ARE BETWEEN CIRCUITS. SEE CHART FOR LOCATION.
10. FEATURE MAY OR MAY NOT EXTEND ACROSS THE ENTIRE FACE OF THE PART.
SEE DETAIL Z.
11. CIRCUIT 1 DESIGNATION IS USED TO DEFINE VOID LOCATION. CIRCUIT 1 MAY
OR MAY NOT LINE UP WITH CIRCUIT 1 ON THE MATING HOUSING.
12. THE PARTS LISTED ON THIS DRAWING ARE CONSTRUCTED TO MEET THE
REQUIREMENT FOR DIRECT SUPPORT OF UNINSULATED LIVE PARTS AS
DESCRIBED IN UL508C.
5.11
.201
AT DATUM -D-
2.41
.095
REF
11.33
±
0.51
.446
±
.020
M
±
0.38
±
.015
TYP
SEE NOTE 10
AND DETAIL Z
P
TYP
REF
10.01
±
0.51
.394
±
.020
CENTERLINE OF PIN AT TIP
NOT TO VARY FROM CENTERLINE
OF PIN AT DATUM -E- BY MORE
THAN 0.13/.005 IN ANY DIRECTION.
SEE DETAIL Z
SEE NOTE 10
TIN
GOLD
DIM. A REF
3.96
.156
REF.
TYP. BETWEEN ANY
2 CONSECUTIVE
CKTS. AT -D-
DIM. B
1.91
.075
AT -D-
CENTERLINE OF PIN AT TIP
NOT TO VARY FROM CENTERLINE
OF PIN AT DATUM -D- BY MORE
THAN 0.20/.008 IN ANY DIRECTION.
CIRCUIT NO. 1
SEE NOTE 11
SEE NOTE 9
3.30
±
0.25
.130
±
.010
OPTIONAL VOIDED CIRCUIT
SEE CHART FOR LOCATION
3.96
±
0.05
.156
±
.002
TYP
5.08
.200
MIN
1.73
±
0.05
.068
±
.002
DIA TYP
7.42
.292
REF
6.10
.200
REF
16.10
.634
REF
CIRCUIT
SIZE
DIM. A DIM. B
SLOT LOCATION
BETWEEN CIRCUITS
2
7.77
.306
3.96
±
0.05
.156
±
.002
NONE
3
11.73
.462
7.92
±
0.10
.312
±
.004
NONE
4
15.70
.618
11.89
±
0.15
.468
±
.006
NONE
5
19.66
.774
15.85
±
0.15
.624
±
.006
NONE
6
23.62
.930
19.81
±
0.18
.780
±
.007
3 & 4
7
27.58
1.086
23.77
±
0.18
.936
±
.007
4 & 5
8
31.55
1.242
27.74
±
0.20
1.092
±
.008
4 & 5
9
35.51
1.398
31.70
±
0.20
1.248
±
.008
5 & 6
10
39.47
1.554
35.66
±
0.23
1.404
±
.009
5 & 6
11
43.43
1.710
39.62
±
0.23
1.560
±
.009
6 & 7
12
47.40
1.866
43.59
±
0.25
1.716
±
.010
4 & 5
8 & 9
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
FEATURE MAY BE ON EITHER
SIDE OF THE PART
