Statguard
®
Dissipative Floor Cleaner
Statguard
®
Floor Cleaner is formulated with dissipative
agents that will rejuvenate and improve the static
dissipative properties of floors treated with Statguard
®
Low-VOC Floor Finish. Statguard
®
Dissipative Cleaner
effectively cleans without leaving behind any harmful
residue that can dull the surface or impede dissipation
properties. Statguard
®
Floor Cleaner is a non-alkaline
detergent with a neutral pH, which requires no rinsing.
Use the following procedure to clean treated floors
with Statguard
®
Floor Cleaner. This product is also
recommended for use on conductive floor tile and
epoxy.
CLEANING SCHEDULE
Heavy to moderate traffic floors should be cleaned once a
week or as needed. Light traffic floors should be cleaned as
needed. Allow the floor finish to dry for at least seven days
before performing any wet maintenance.
Equipment needed:
• Push broom
• Mop (dedicated to Statguard
®
Floor Cleaner use only)
• Buckets
• Statguard floor cleaner Dissipative Cleaner
1. Always use in a well ventilated area. Wear appropriate
eye protection such as splash goggles and impervious
type protective gloves.
2. Dry mop the surface to be cleaned.
3. Dilute Statguard
®
Dissipative Cleaner 10:1, two quart
of cleaner concentrate to five gallons of clean water.
4. Thoroughly shake the cleaner concentrate container
before pouring the cleaner into the bucket. Use a clean
untreated mop (dedicated to Statguard
®
Floor Cleaner
use only) to damp mop the area. Wring out excess fluid
so mop is not dripping and do not flood a treated floor
with water. Do not use scrubbing machine to clean the
floor.
5. Allow 20 to 40 minutes drying time before walking on the
cleaned area.
TB-7055 Page 4 of 13
© 2012 DESCO INDUSTRIES, INC.
Employee Owned
DESCO INDUSTRIES INC. • 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 • Fax (909) 627-7449 • Web Site: DescoIndustries.com
If Statguard
®
Low-VOC Floor Finish freezes, allow it to
thaw to 70°F before application.
1. Always use in a well ventilated area. Wear
appropriate eye protection such as splash goggles
and impervious type protective gloves.
2. Pour Floor Finish into a clean bucket. Apply using a
damp clean rayon or cotton mop. Make sure to use
a dedicated mop, do not use a mop that has been
used to strip or mop floors. Coat the floor uniformly,
avoiding excessive foaming.
3. Allow the first coat to dry for a minimum of 60
minutes, and then apply the second coat.
4. If it is for a high traffic application and the humidity is
above 30% RH, repeat step three for the third coat.
5. Allow last coat to dry overnight or minimum of six
hours before permitting any kind of floor traffic on
the newly coated area. An overnight curing time is
preferred.
6. Allow minimum of seven days of drying time before
performing any wet maintenance (spray buffing,
burnishing, and floor cleaner) on newly coated
floor. Premature wet maintenance will negatively
effect film formation and electrical properties.
Floor Finish Maintenance
Preventative maintenance is important to maintain the
electrical properties and appearance of the finish. The
use of carpet runners and tack mats are suggested
when areas of high dirt or other contaminants are
leading onto Statguard
®
Low-VOC Floor Finish areas.
Although wet maintenance can be performed after
seven days of drying, Statguard
®
Low-VOC Floor
Finish electrical properties can last three to four months
with regular dry maintenance.
DRY MOP PROGRAM
Keep the floor surface clean. Use an untreated dust
mop or push broom daily to remove accumulated dirt
and insulative contaminants.
Figure 6. Statguard
®
Dissipative Floor Cleaner: 5 gallon
bag-in-box
