MAX6315
Open-Drain SOT µP Reset Circuit
Maxim Integrated | 4www.maximintegrated.com
Detailed Description
Reset Output
A microprocessor’s (µP’s) reset input starts the µP in a
known state. The MAX6315 asserts reset to prevent
code-execution errors during power-up, power-
down, or brownout conditions. RESET is guaranteed to
be a logic-low for V
CC
> 1V (see the
Electrical
Characteristics
table). Once V
CC
exceeds the reset
threshold, the internal timer keeps RESET asserted for
the reset timeout period (t
RP
); after this interval RESET
goes high. If a brownout condition occurs (monitored
voltage dips below its programmed reset threshold),
RESET goes low. Any time V
CC
dips below the reset
threshold, the internal timer resets to zero and RESET
goes low. The internal timer starts when V
CC
returns
above the reset threshold, and RESET remains low for
the reset timeout period.
The MAX6315’s RESET output structure is a simple
open-drain n-channel MOSFET switch. Connect a pull-
up resistor to any supply in the 0V to +6V range. Select
a resistor value large enough to register a logic low
when RESET is asserted (see the
Electrical
Characteristics
table), and small enough to register a
logic high while supplying all input current and leakage
paths connected to the RESET line. A 10kΩ pullup is
sufficient in most applications.
Often, the pullup connected to the MAX6315’s RESET
output will connect to the supply voltage monitored at
the IC’s V
CC
pin. However, some systems may use the
open-drain output to level-shift from the monitored
supply to reset circuitry powered by some other supply
(Figure 1). This is one useful feature of an open-drain
output. Keep in mind that as the MAX6315’s V
CC
decreases below 1V, so does the IC’s ability to sink
current at RESET. Finally, with any pullup, RESET will
be pulled high as V
CC
decays toward 0V. The voltage
where this occurs depends on the pullup resistor value
and the voltage to which it connects (see the
Electrical
Characteristics
table).
Manual-Reset Input
Many µP-based products require manual-reset capa-
bility, allowing the operator, a test technician, or exter-
nal logic circuitry to initiate a reset. A logic low on MR
asserts reset. Reset remains asserted while MR is low,
and for the reset active timeout period after MR
returns high.
MR has an internal 63kΩ pullup resistor, so it can be
left open if not used. Connect a normally open momen-
tary switch from MR to GND to create a manual-reset
function; external debounce circuitry is not required.
If MR is driven from long cables or if the device is used
in a noisy environment, connecting a 0.1µF capacitor
from MR to ground provides additional noise immunity.
Applications Information
Negative-Going V
CC
Transients
In addition to issuing a reset to the µP during power-up,
power-down, and brownout conditions, these devices
are relatively immune to short-duration negative-going
transients (glitches). The
Typical Operating Character-
istics
show the Maximum Transient Duration vs. Reset
Comparator Overdrive, for which reset pulses are not
generated. The graph was produced using negative-
going pulses, starting at V
RST
max and ending below
the programmed reset threshold by the magnitude indi-
cated (reset threshold overdrive). The graph shows the
maximum pulse width that a negative-going V
CC
tran-
sient may typically have without causing a reset pulse
to be issued. As the transient amplitude increases (i.e.,
goes farther below the reset threshold), the maximum
allowable pulse width decreases. A 0.1µF bypass
capacitor mounted close to V
CC
provides additional
transient immunity.
Figure 1. MAX6315 Open-Drain RESET Output Allows Use
with Multiple Supplies