OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AH180N-WG-7

P1-P3P4-P6P7-P8
AH180N
Document number: DS32174 Rev. 4 - 2
1 of 8
www.diodes.com
August 2012
© Diodes Incorporated
A
H180N
MICROPOWER OMNIPOLAR HALL-EFFECT SWITCH
Description
The AH180N is a high sensitivity, micro power Omnipolar Hall Effect
switch IC designed for portable and battery powered equipment such
as cellular phones, PDA’ s and portable PC’ s. Based on two sensitive
Hall Effect plates and a chopper stabilized architecture the AH180N
provides a reliable solution over the whole operating range. To
support portable and battery powered equipment the design has been
optimized to operate over the supply range of 2.5V to 5.5V and
consumes only 24µA with a supply of 3V.
The single open drain output can switched on with either a North or
South pole of sufficient strength. When the magnetic flux density (B)
is larger than operate point (Bop) the output is switched on (pulled
low). The output is turned off when B becomes lower than the release
point (Brp). The output will remain off when there is no magnetic field.
Features
• Omnipolar (North or South pole) Operation
• High Sensitivity
• Single Open Drain Output
• Micropower Operation
• 2.5V to 5.5V Operating Range
• Chopper Stabilized Design Provides
Superior Temperature Stability
Minimal Switch Point Drift
Enhanced Immunity to Stress
• Good RF Noise Immunity
• -40°C to +85°C Operating Temperature
• ESD (HBM) > 6KV
• SC59 (SOT23), TSOT23, and SOT553 Low Profile Packages
• Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
• Halogen and Antimony Free. “Green” Device (Note 3)
Pin Assignments
Applications
• Cover Switch in Clam-Shell or Slide Type Cellular Phones
• Display Switch for Portable PCs
• On/Off Switch for PDAs and Digital Cameras
• Contact-Less Switch in Consumer Products
Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl)
and <1000ppm antimony compounds.
AH180N
Document number: DS32174 Rev. 4 - 2
2 of 8
www.diodes.com
August 2012
© Diodes Incorporated
A
H180N
Typical Applications Circuit
AH180N
2.5V to 5.5V
OUTPUT
GND
R
L
C
Note: C is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 10nF ~ 100nF.
R
L
is the pull-up resistor, the recommended resistance is 10kOhm ~ 100kOhm.
V
DD
Pin Descriptions
Functional Block Diagram
Offset
Cancelling
Offset
Cancelling
Pin Name P/I/O Function
V
DD
P/I Power Supply Input
GND P/I Ground
Output O Output Pin
AH180N
Document number: DS32174 Rev. 4 - 2
3 of 8
www.diodes.com
August 2012
© Diodes Incorporated
A
H180N
Absolute Maximum Ratings (Note 4) (@T
A
= +25°C, unless otherwise specified.)
Symbol Parameter Ratings Unit
V
DD
Supply Voltage (Note 5) 7 V
B Magnetic Flux Density Unlimited
P
D
Package Power Dissipation
SC59 230
mW TSOT23 230
SOT553 230
Ts Storage Temperature Range -65 to +150
°C
T
J
Maximum Junction Temperature 150
°C
Notes: 4. Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings
only; functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device
reliability may be affected by exposure to absolute maximum rating conditions for extended periods of time
5. The absolute maximum V
DD
of 7V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to
operate the device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (@T
A
= +25°C, unless otherwise specified.)
Symbol Parameter Conditions Rating Unit
V
DD
Supply Voltage Operating 2.5 to 5.5 V
T
A
Operating Temperature Range Operating -40 to +85
°C
Electrical Characteristics (@T
A
= +25°C, V
DD
= 3V, unless otherwise specified.)
Symbol Parameter Conditions Min Typ Max Unit
V
OUT
Output On Voltage I
OUT
= 1mA
⎯
0.1 0.3 V
Ioff Output Leakage Current V
OUT
= 5.5V, Output Off
⎯
<0.1 1 µA
Idd(en)
Supply Current
Chip Enable, T
A
= +25°C, V
DD
= 3V
⎯
3 6 mA
Idd(en)
Chip Enable, T
A
= -40 to +85°C,
V
DD
= 2.5V to 5.5V
⎯
3 12 mA
Idd(dis)
Chip Disable, T
A
= +25°C, V
DD
= 3V
⎯
5 10 µA
Idd(dis)
Chip Disable, T
A
= -40 to 85°C,
V
DD
= 2.5V to 5.5V
⎯
5 28 µA
Idd(avg)
Average Supply Current,
T
A
= +25°C, V
DD
= 3V
⎯
8 16 µA
Idd(avg)
Average Supply Current,
T
A
= -40 to +85°C, V
DD
= 2.5V to 5.5V
⎯
8 40 µA
Tawake Awake Time (Note 6)
⎯
75 125 µs
Tperiod Period (Note 6)
⎯
75 125 ms
D.C. Duty Cycle
⎯
0.1
⎯
%
Notes: 6. When power is initially turned on, V
DD
must be within its correct operating range (2.5V to 5.5V) to guaranteed the output sampling.
The output state is valid after the second operating cycle (typical 150ms).
Idd (dis)
Idd(en)
Tawake
Tperiod
0
Sample and output
latched
P1-P3P4-P6P7-P8

AH180N-WG-7

Mfr. #:
Buy AH180N-WG-7
Manufacturer:
Diodes Incorporated
Description:
Board Mount Hall Effect / Magnetic Sensors Omni-polar 2.5V-5.5V EDS 6kV Vdd 7V
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet