80181012

Brushless gearmotor
80 181 012 Series
Data sheet
0/10V - ratio 20
801810 TNI20
Parallel key 4 x 4 x 20 DIN6885A 8 x M5, depth 8 Input - Output cable with Molex connector - 500 mm +- 20
4 x M4, depth 8 over diameter 36 mm 4 x holes D. 3,8 mm, depth 10 over diameter 40 mm Power supply cable - 500 mm +- 20
General characteristics
Power supply Drive
Direct current voltage supply
Type
Nominal voltage range
Vdc 18 -> 32
Built-in drive
Max. current A
Internal encoder 12 pulses per turn
Control
Gearmotor type 801810 TNI20
Speed
0/10 V
Motor type
80 180 002
Torque
0/10 V
Gearbox type
81 041 0
4 quadrants - low braking
Ratio
4 quadrants with regenerative energy
Shaft output
Left
"Trapezoidal" type
Max. permissible continuous torque
Nm
Security
Max. backlash
°
Short-circuit of outputs
Input inverted
Motor characteristics (1)
Low voltage Vdc < 14
At no load
Short high voltage Vdc > 36
Max. output speed
rpm
Stop at max internal drive temperature (2) °C
Current at the max output speed (6)
A
Drive temperature allowing to restart
°C
Standby current
A
At nominal
Generic parameters
Speed
rpm +-15%
Output shaft with ball bearings
Torque (2)
Nm
Max. Radial force
(12mm from front face)
N
Output power
W +-15%
Max. axial force(4)
N
Current
A
Temperature range
CEI60068-2-1/2
°C -30 -> +70
Efficiency
%
Storage temperature °C -40 -> +80
At max. output power
Dielectric
1min 2mA 50Hz CEI60335
Vac
Speed
rpm
Motor insulation
CEI60085
class
Torque
Nm
Salt spray
CEI60068-2-58
severity
48h
Output power
W
CEI60529
IP
Current
A
(output shaft not included)
Efficiency
%
EMC
At peak torque
Electrostatic Discharge
CEI61000-4-2
level 3
Speed
rpm
Radio frequency
CEI61000-4-3
level 3
Torque
Nm
Electrical fast transsient / burst test
CEI61000-4-4
level 3
Output power
W
Surge test
CEI61000-4-5
level 1
Current
A
Conducted disturbance
CEI61000-4-6
level 3
Others
Radiated emission
EN55022
class B
Weight
kg
Approvals
Noise level
dBA ROHS
2011/65/UE
EC
2014/30/UE
Connecting
Input - Output cable
With Molex connector ref: 43025-0800
Output cable, UL style 2464 80°C 300V - 8 wires AWG24
Input: ON/OFF 1 - Green
Input: Direction
2 - Yellow
Input: Torque limit
3 - Blue
Notes
Input: Speed 4 - Orange
0V
5 - Black
Output: Pulse 6 - Brown
(1) Cold motor, 20 ° C ambient temperature, full speed
Output: Torque limit reached 7 - Purple
Output: Direction 8 - Red
Power supply cable
Cable UL style 2464 80°C 300V - 2 wires AWG20 - 500 mm
+ 18Vcc -> + 32 Vdc
Brown
0V Black
Specifications subject to change without notice. Updated 21/11/2016
Crouzet Automatismes
12, rue Jean Jullien-Davin - CS 60059
www.crouzet-motors.com
26902 Valence CEDEX 9 France
Series 801810 TNI20
(6) Value without gearbox. With gearbox, the value increases and varies depending on grease
temperature.
(4) Pinion or pulley fitting are done at the Crouzet factory, before final assembly.
2,04
45
Values without tolerance are average production values.
Motor not protected in case of reversed power voltage
(2) Max torque for continuous operation at 20 ° C, decrease this value for higher ambient
temperature
50
6,0
150
3,2
6,0
35
3,2
50
150
44
100
4,8
163
2,6
80 181 012 - 0/10V - ratio 20
210
110
0,39
90
150
E
38
1 000
54
TNI20
6
0,5
24 Vdc
20
10
3
2
1
4
3
2
1
6
5
4
5
6
Drive electrical datas
Absolute maximum ratings Input datas
Parameters Parameters
Max. voltage supply "Vcc" Impedance - Input 1, 2 (On/Off - Direction)
Max. current "Icc max" Impedance - Input 3 (torque)
Max. voltage on inputs "Vin max" Impedance - Input 4 (speed)
Max. voltage on outputs "Vout max" Low level - Input 1, 2
Max. output current "Iout max" HIgh level - Input 1, 2
Running datas
Voltage level - Input 3, 4
Parameters
Voltage suplly "Vcc"
Current "Icc"
Output datas
Standby power "Wo"
Parameters
Speed setting
0 /
Low level Outputs
Vdc
Torque setting with "pull down resistor" = 4,7K and Vcc = 24 V
High level Outputs
Vdc
with "pull down resistor" = 4,7K and Vcc = 24 V
= voltage supply added from eventual rejective voltage
Notes
Outputs are destroyed if they are connected to zero ground or to a capacitive load
Speed-torque and current-torque curves
Torque (Nm) Torque (Nm)
Nominal torque Peak torque
Wiring Output equivalent circuit
Outputs
Add a pull down resistor
ON /OFF Encoder pulse
Direction Max. torque reached
Torque Real direction
Speed
0 Volt
Vcc
Output
0 Volt
Pull down resistor
0 Volt
Input equivalent circuits
Inputs 1; 2: ON/OFF and Direction Input 4: Speed (if 0/10 V drive)
Input Input
0 Volt 0 Volt
Input 3: Torque Input 4: Speed (if PWM drive)
Input Input
0 Volt 0 Volt
Specifications subject to change without notice. Updated 21/11/2016
Crouzet Automatismes
12, rue Jean Jullien-Davin - CS 60059
www.crouzet-motors.com
26902 Valence CEDEX 9 France
Series 801810 TNI20
TNI20
18 -> 32 Vdc
Brushless motor
Vcc
Nm 1,1
-
3,2
Vcc - 0,5
-
Speed (rpm)
Current (A)
rpm
-
210
Max
W - 2 -
0 - 0,2
6
A - 4 6
Min Typical
Vdc 18 24 32
Min Typical Max
Hz
-
Vdc
-
mA 50
Vdc
0 0/10 36
Vdc 36
Vdc 4 - 36
36
Vdc 0 - 2
A 6 k - 16,4 -
Vdc k - 440 -
80 181 012 - 0/10V - ratio 20
Max
Vdc 36 k - 59 -
Min Typical
0
1
2
3
4
5
6
7
0 0,5 1 1,5 2 2,5 3 3,5
0
50
100
150
200
250
0 0,5 1 1,5 2 2,5 3 3,5
1
2
3
4
5
6
7
8
4k
7

80181012

Mfr. #:
Manufacturer:
Crouzet
Description:
AC, DC & Servo Motors BLDC 80 W RAP=20 24V
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet