External Visual
No abnormal exterior appearance Microscope (´10)
Physical Dimension
Within the specified dimensions Using The calipers
Mechanical Shock
Appearance : No abnormal exterior appearance Three shocks in each direction should be applied along
Capacitance Change Within ±10 % 3 mutually perpendicular axes of the test specimen (18 shocks)
Tan δ, IR : Initial spec.
Initial Measurement 2*
Final Measurement 5*
Vibration
Appearance : No abnormal exterior appearance 5g's for 20min., 12cycles each of 3 orientations,
Capacitance Change Within ±10 % Use 8"×5" PCB 0.031" Thick 7 secure points on one long side
Tan δ, IR : Initial spec. and 2 secure points at corners of opposite sides. Parts mounted
within 2" from any secure point. Test from 10~2,000㎐.
Initial Measurement 2*
Final Measurement 5*
Resistance to
Appearance : No abnormal exterior appearance
preheating : 150℃ for 60~120 sec.
Solder Heat
Capacitance Change Within ±10 %
Solder pot : 260±5℃, 10±1sec.
Tan δ, IR : Initial spec. Initial Measurement 2*
Final Measurement 3*
ESD
Appearance : No abnormal exterior appearance
AEC-Q200-002 or ISO/DIS10605
Capacitance Change Within ±10 % Initial Measurement 2*
Tan δ, IR : Initial spec. Final Measurement 4*
Solderability
95% of the terminations is to be soldered
a) Preheat at 155℃ for 4 hours, Immerse in solder for 5s at 245±5℃
evenly and continuously
b) Steam aging for 8 hours, Immerse in solder for 5s at 245±5℃
c) Steam aging for 8 hours, Immerse in solder for 120s at 260±5℃
solder : a solution ethanol and rosin
Electrical
Capacitance : Within specified tolerance *A capacitor prior to measuring the capacitance is heat treated at
Characterization
Tan δ
0.05 max.
150 +0/-10℃ for 1hour and maintained in ambient air for 24±2 hours
IR(25℃) :
More than 10,000 ㏁ or 500 ㏁×㎌
The Capacitance / D.F. should be measured at 25℃,
Whichever is smaller 1 ㎑ ± 10%, 1 ± 0.2 Vrms
IR(125℃) More than 1,000 ㏁ or 10 ㏁×㎌ I.R. should be measured with a DC voltage not exceeding
Whichever is smaller Rated Voltage @25℃, @125℃ for 60~120 sec.
Dielectric Strength Dielectric Strength : 250% of the rated voltage for 1~5 seconds
Board Flex
Appearance : No abnormal exterior appearance Bending to the limit, 3 ㎜ for 60 seconds 1*
Capacitance Change Within ±10 % Initial Measurement 2*
Final Measurement 5*
Terminal
Appearance : No abnormal exterior appearance 2 N, for 60 sec.
Strength(SMD)
Capacitance Change Within ±10 % Initial Measurement 2*
Final Measurement 5*
Beam Load
Destruction value should be exceed 8 N Beam speed : 0.5±0.05 ㎜/sec
Temperature
X7R
Characteristics
From -55 ℃ to 125 ℃, Capacitance change should be within ±15%
D. Recommended Soldering method :
Reflow ( Reflow Peak Temperature : 260 +0/-5℃, 30sec. ), Meet IPC/JEDEC J-STD-020 D Standard
*1 : The figure indicates typical specification. Please refer to individual specifications.
*2 : Initial measurement : Perform a heat treatment at 150 +0/-10℃ for one hour after soldering process.
and then let sit for 24±2 hours at room temperature. Perform the initial measurement.
*3 : Final measurement : Let sit for 24±2 hours at room temperature after test conclusion, then measure.
*4 : Final measurement : Perform a heat treatment at 150 +0/-10℃ for one hour after soldering process.
and then let sit for 24±2 hours at room temperature. Perform the initial measurement.
*5 : Final measurement : Let measure within 24 hours at room temperature after test conclusion.
Product specifications included in the specifications are effective as of March 1, 2013.
Please be advised that they are standard product specifications for reference only.
We may change, modify or discontinue the product specifications without notice at any time.
So, you need to approve the product specifications before placing an order.
Should you have any question regarding the product specifications, please contact our sales personnel or application engineers.
0.5ms Half sine 4.7m/sec
Performance Test condition
Peak value Duration Wave Velocity
1,500G
