OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

FCM3.25-A-L14

P1-P3P4-P6P7-P8
4
Proper Installation Steps
Surface Preparation
For best results, mounts should be applied to a clean, dry, and grease-free surface. It is recommended that for each individual application,
a solvent or cleanser be used to thoroughly prepare the surface for mount installation. The following are recommended cleaning guidelines:
1. For Rubber and Acrylic-based Adhesive Foam Tape, a mixture of water and isopropyl alcohol may be used on
most surfaces.
For Two-part Epoxy Adhesive, especially on masonry surfaces, be sure to clean all loose particles away before
mount installation. Some surface abrasion is recommended on smooth surfaces to achieve maximum strength.
A light rubbing with medium grit emery cloth or sandpaper is best. Wash the surface after abrading.
2. Allow the surface to dry completely before applying the mount.
1. For proper installation of adhesive backed mounts with foam tape, remove the release liner from the foam
adhesive. Without touching the adhesive, place the mount in the desired location.
For Two-part Epoxy Adhesive Mounts, apply 1/3 of the mixed adhesive to the bottom of the
PANDUIT
®
EMS or
ASMS mount. Without touching the adhesive, place the mount in the desired location.
2. Apply firm pressure for five (5) seconds to the foam tape mounts to insure proper adhesion.
Two-part Epoxy Adhesive Mounts should be twisted in place to ensure the adhesive is forced into the
porous surface.
3. Allow the mount to remain in place for the recommended dwell time for the specific adhesive being used.
The dwell time for Rubber-based Adhesive Foam Tape is two (2) hours and for Acrylic-based Adhesive Foam
Tape it is eight (8) hours.
Two-part Epoxy Adhesive Mounts can support about 5 lbs. after first fifteen (15) minutes. The adhesive fully
cures after twenty-four (24) hours and bonding strength will exceed 50 lbs.
4. The mount is now ready to be used.
Installing the Mount
Alcohol
12
6
3
9
5
Mount Spacing
To determine the number of mounts to use in a given application, the following formula can be used as a guideline:
For example, to determine the mount spacing using part number ABM2S-A-C for an application with a bundle of wires that weigh one
pound per foot, the formula would be:
Proper Storage Conditions
Mounts and adhesives should be kept in the original packaging until they are ready to be applied. Store at room temperature 70°F (21°C)
with 45% or less relative humidity. Avoid storing adhesive products near heating vents or other heating sources.
Using the guidelines above, the average shelf life of adhesive foam tape is three (3) years from the date of manufacture. The shelf life of
Two-part Epoxy Adhesive is one (1) year from the date of manufacture. Failing to follow the recommended storage conditions may reduce
the shelf life or adhesive strength of the foam tape and Two-part Epoxy Adhesive.
Adhesive Technical Information
Adhesive foam tape properties are developed with thorough laboratory research and testing. The double-coated adhesive foam tape used
on
PANDUIT
®
Adhesive Backed Mounts is manufactured under strict quality requirements, which provide consistent, high quality
performance for use on adhesive mounts. Each package of mounts has an expiration date and a Quality Control number printed on the
label, which permit traceability.
Double Coated Foam Tape Properties
Polyethylene
(In.) Total
Less Liner
6
.040
.035
Polyethylene
6
.039
.034
Rubber Adhesive
Acrylic Adhesive
Cable bundle weight in lbs/foot
Minimum number of
mounts per foot
=
Maximum static load rating of the mount*
1 pound per foot
0.5 lbs load rating
2 mounts per foot
=
* See pages 6-7 for static load ratings.
Backing Material
Nominal Backing Density (pcf)
Thickness (PSTC-33)
Static Shear MIL-T-60394A (Hours)
72°F/17.6 psi
72°F/8.8 psi
158°F/2.s psi
500+
1000+
100+
N/A
N/A
200+
6
ABM
ABMT
PLA
SMS
AJC
A2C
MACC
LWC
Adhesive Backed Mounts and Clips
Part Number Material
Length Width Max. Static Load
Adhesive Type
Std.
Pkg.
Qty.‡
In. mm In. mm Lbs. g
4-Way Adhesive Backed Mounts
ABM1M-A-C Nylon 6.6 .50 12.7 .50 12.7 .13 59 Rubber 100
ABMM-A-C ABS .75 19.1 .75 19.1 .30 136 Rubber 100
ABM2S-A-C ABS 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM100-A-C Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM112-A-C Nylon 6.6 1.12 28.6 1.12 28.6 .63 286 Rubber 100
ABM3H-A-L Nylon 6.6 1.50 38.1 1.50 38.1 1.12 508 Rubber 50
ABM4H-A-L Nylon 6.6 2.00 50.8 2.00 50.8 2.00 907 Rubber 50
T
AK
-T
Y
®
Hook & Loop Cable Tie Mounts
ABMT-A-C Nylon 6.6 1.10 28.7 1.10 28.6 .38 174 Rubber 100
ABMT-A-C20 Nylon 6.6 1.10 28.7 1.10 28.6 .38 174 Rubber 100
Combination Adhesive Mount/Cable Ties
PLA2S-A-Q Nylon 6.6 1.00 25.4 .90 22.9 .45 204 Rubber 25
PRA2S-A-Q Nylon 6.6 1.00 25.4 .90 22.9 .45 204 Rubber 25
Snap-In Cable Tie Mount
SMS-A-C ABS 2.00 50.8 1.00 25.4 1.00 454 Rubber 100
C
LINCHER
™
Adjustable Releasable Clamp
ARC.68-A-Q Polypropylene 1.00 25.4 1.00 25.4 .50 227 Rubber 25
Adhesive Backed Cord Clips
ACC19-A-C Nylon 6.6 .63 16.0 .76 19.3 .20 91 Rubber 100
ACC38-A-C Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ACC62-A-C Nylon 6.6 1.25 31.7 1.12 28.6 .70 318 Rubber 100
“J” Clips
AJC12-A-C PVC 1.00 25.4 .86 21.8 .40 182 Rubber 100
AJC19-A-C PVC 1.25 31.8 .89 22.6 .50 227 Rubber 100
AJC31-A-C PVC 1.75 44.5 1.23 31.2 .90 408 Rubber 100
AJC38-A-C PVC 2.00 50.8 1.28 32.5 1.00 454 Rubber 100
A1C Type Clips
A1C12-A-C8 PVC .77 19.6 .63 16.0 .14 64 Rubber 100
A1C25-A-C8 PVC .91 23.1 .63 16.0 .14 64 Rubber 100
A1C38-A-C8 PVC 1.04 26.4 .63 16.0 .14 64 Rubber 100
A1C50-A-C8 PVC 1.17 29.7 .63 16.0 .14 64 Rubber 100
A2C Type Clips
A2C12-A-C8 PVC 1.30 33.0 .63 16.0 .14 64 Rubber 100
A2C25-A-C8 PVC 1.43 36.3 .63 16.0 .14 64 Rubber 100
A2C38-A-C8 PVC 1.56 39.6 .63 16.0 .14 64 Rubber 100
A2C50-A-C8 PVC 1.68 42.7 .63 16.0 .14 64 Rubber 100
Metal Adhesive Backed Cord Clips
MACC25-A-C Zinc Plated Steel .79 20.0 .53 13.5 .21 95 Rubber 100
MACC62-A-C Zinc Plated Steel 1.18 30.0 .75 19.1 .44 200 Rubber 100
Latching Wire Clips
LWC19-A-C Nylon 6.6 .85 21.6 .61 15.5 .25 113 Rubber 100
LWC25-A-C Nylon 6.6 .88 22.2 1.00 25.4 .45 204 Rubber 100
LWC38-A-C Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
LWC50-A-L Nylon 6.6 1.26 32.0 1.00 25.4 .63 272 Rubber 50
LWC75-A-L Nylon 6.6 1.48 37.6 1.24 31.5 .93 417 Rubber 50
LWC100-A-L Nylon 6.6 2.21 56.1 1.97 50.0 2.25 1020 Rubber 50
ARC
ACC
A1C
Contact customer service (800-777-3300) for additional sizes, materials, and acrylic tape availability or visit www.panduit.com.
‡ Order the number of pieces required, in multiples of Standard Package Quantity.
P1-P3P4-P6P7-P8

FCM3.25-A-L14

Mfr. #:
Buy FCM3.25-A-L14
Manufacturer:
Panduit
Description:
Cable Mounting & Accessories FLAT CBL 3.25 ADH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet