LTC3728L-1
8
3728l1fc
PIN FUNCTIONS
V
OSENSE1
, V
OSENSE2
: Error Amplifi er Feedback Input.
Receives the remotely-sensed feedback voltage for each
controller from an external resistive divider across the
output.
PLLFLTR: Filter Connection for Phase-Locked Loop. Alter-
natively, this pin can be driven with an AC or DC voltage
source to vary the frequency of the internal oscillator.
PLLIN: External Synchronization Input to Phase Detector.
This pin is internally terminated to SGND with 50k. The
phase-locked loop will force the rising top gate signal of
controller 1 to be synchronized with the rising edge of
the PLLIN signal.
FCB: Forced Continuous Control Input. This input acts
on both controllers and is normally used to regulate a
secondary winding. Pulling this pin below 0.8V will force
continuous synchronous operation.
I
TH1,
I
TH2
: Error Amplifi er Output and Switching Regulator
Compensation Point. Each associated channels’ current
comparator trip point increases with this control voltage.
SGND: Small Signal Ground. Common to both controllers,
this pin must be routed separately from high current
grounds to the common (–) terminals of the C
OUT
capacitors.
3.3V
OUT
: Linear Regulator Output. Capable of supplying
10mA DC with peak currents as high as 50mA.
NC: No Connect.
SENSE2
–
, SENSE1
–
: The (–) Input to the Differential Cur-
rent Comparators.
SENSE2
+
, SENSE1
+
: The (+) Input to the Differential Current
Comparators. The I
TH
pin voltage and controlled offsets
between the SENSE
–
and SENSE
+
pins in conjunction with
R
SENSE
set the current trip threshold.
RUN/SS2, RUN/SS1: Combination of soft-start and run
control inputs. A capacitor to ground at each of these pins
sets the ramp time to full output current. Forcing either of
these pins back below 1.0V causes the IC to shut down
the circuitry required for that particular controller.
TG2, TG1: High Current Gate Drives for Top N-Channel
MOSFETs. These are the outputs of fl oating drivers with
a voltage swing equal to INTV
CC
– 0.5V superimposed on
the switch node voltage SW.
SW2, SW1: Switch Node Connections to Inductors. Voltage
swing at these pins is from a Schottky diode (external)
voltage drop below ground to V
IN
.
BOOST2, BOOST1: Bootstrapped Supplies to the Top
Side Floating Drivers. Capacitors are connected between
the boost and switch pins and Schottky diodes are tied
between the boost and INTV
CC
pins. Voltage swing at the
boost pins is from INTV
CC
to (V
IN
+ INTV
CC
).
BG2, BG1: High Current Gate Drives for Bottom (Synchro-
nous) N-Channel MOSFETs. Voltage swing at these pins
is from ground to INTV
CC
.
PGND: Driver Power Ground. Connects to the sources of
bottom (synchronous) N-channel MOSFETs, anodes of the
Schottky rectifi ers and the (–) terminal(s) of C
IN
.
INTV
CC
: Output of the Internal 5V Linear Low Dropout
Regulator and the EXTV
CC
Switch. The driver and control
circuits are powered from this voltage source. Must be
decoupled to power ground with a minimum of 4.7µF
tantalum or other low ESR capacitor.
EXTV
CC
: External Power Input to an Internal Switch Con-
nected to INTV
CC
. This switch closes and supplies V
CC
power, bypassing the internal
low dropout regulator, when-
ever EXTV
CC
is higher than 4.7V. See EXTV
CC
connection
in Applications section. Do not exceed 7V on this pin.
V
IN
: Main Supply Pin. A bypass capacitor should be tied
between this pin and the signal ground pin.
PGOOD: Open-Drain Logic Output. PGOOD is pulled to
ground when the voltage on either V
OSENSE
pin is not
within ±7.5% of its set point.
Exposed Pad (UH Package Only): Signal Ground. Must
be soldered to the PCB, providing a local ground for the
control components of the IC, and be tied to the PGND
pin under the IC.