CRA06P
www.vishay.com
Vishay
Revision: 24-Jun-13
3
Document Number: 31047
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
(1)
Figures are given for a single element.
(2)
Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years.
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
TEST
(clause)
CONDITIONS OF TEST
REQUIREMENTS
PERMISSIBLE CHANGE (R/R)
(1)
STABILITY
CLASS 1 OR BETTER
STABILITY
CLASS 2 OR BETTER
Stability for product types:
10 to 1 M 10 to 1 M
CRA06P
Resistance (4.5) - ± 1 % ± 2 %; ± 5 %
Temperature coefficient (4.8.4.2)
(20/- 55/20) °C and
(20/125/20) °C
± 100 ppm/K ± 200 ppm/K
Overload (4.13)
U = 2.5 x (P
70
x R)
1/2
2 x U
max.
; 0.5 s
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Solderability (4.17.5)
(2)
Aging 4 h at 155 °C, dryheat
Solder bath method; 235 °C; 2 s
Visual examination
Good tinning ( 95 % covered)
no visible damage
Resistance to soldering heat (4.18.2)
Solder bath method;
(260 ± 5) °C; (10 ± 1) s
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Rapid change of temperature (4.19)
30 min at LCT = - 55 °C;
30 min at UCT = 125 °C; 5 cycles
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Damp heat, steady state (4.24)
(40 ± 2) °C; 56 days;
(93 ± 3) % RH
± (1 % R + 0.05 )± (2 % R + 0.1 )
Climatic sequence (4.23)
16 h at UCT = 125 °C; 1 cycle at 55 °C;
2 h at LCT = - 55 °C;
1 h/1 kPa at 15 °C to 35 °C;
5 cycles at 55 °C
U = (P
70
x R)
1/2
U = U
max.
; whichever is less severe
± (1 % R + 0.05 )± (2 % R + 0.1 )
Endurance at 70 °C (4.25.1)
U = (P
70
x R)
1/2
U = U
max.
; whichever is less severe
1.5 h “ON”; 0.5 h “OFF”;
70 °C; 1000 h
± (1 % R + 0.05 )± (2 % R + 0.1 )
Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 )± (4 % R + 0.1 )
Endurance at upper category
temperature (4.25.3)
UCT = 125 °C; 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )
APPLICABLE SPECIFICATIONS
• EN 60115-1 Generic specification
• EN 140400 Sectional specification
• EN 140401-802 Detail specification
• IEC 60068-2-X Variety of environmental test procedures
• EIA 481 Packaging of SMD components