OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HIH9121-021-001

P1-P3
Honeywell HumidIcon™ Digital
Humidity/Temperature Sensors: SIP 4 Pin
Versions of the HIH6000 Series, HIH7000
Series, HIH8000 Series, HIH9000 Series
Sensing and Control
1.0 GENERAL INFORMATION
The following additional technical information is available for
reference on the Web:
Product data sheets for the HIH6000 Series, HIH7000
Series, HIH8000 Series, and HIH9000 Series
Product Application note
Application sheets:
– Humidity Sensor Performance Characteristics
– Humidity Sensor Theory and Behavior
– Humidity Sensor Moisture and Psychrometrics
– Humidity Sensor Chemical Resistivity
– Thermoset Polymer-based Capacitive Sensors
Technical Notes:
– Entering and Using Command Mode on the Honeywell
HumidIcon™ Digital Humidity/Temperature Sensors
– Total Error Band Specification for Honeywell Digital
Humidity/Temperature Sensors
2.0 SENSOR HANDLING
CAUTION
IMPROPER HANDLING
Do not remove the sensor from its original protective
packaging until it is ready to be installed.
Do not touch the sensor surface. Use latex finger cots.
Handle the sensor by its package edges or leads.
Do not allow objects to enter the cavity of the sensor
element.
Do not allow debris or contaminants to accumulate on
the filter.
Failure to comply with these instructions may result in
product damage.
3.0 SENSOR CLEANING
CAUTION
IMPROPER CLEANING
Insert and solder the sensor after the PCB cleaning
process.
Failure to comply with these instructions may result in
product damage.
4.0 SENSOR POSITIONING
CAUTION
IMPROPER SENSOR POSITIONING
Position the sensor so that its face is exposed to the
atmosphere being monitored.
Ensure dust and condensation are avoided.
Failure to comply with these instructions may result in
product damage.
5.0 SENSOR SOLDERING
CAUTION
IMPROPER SOLDERING
For better product reliability, the sensor is factory-
shipped with a protective tape on the cover (sensing
face). This tape must remain in place during soldering.
After soldering, remove the protective tape as described
below to activate the sensor.
Failure to comply with these instructions may result in
product damage.
Automated: Use a no-clean flux. Limit the contact of the
flux to the leads only. Reflow soldering profile specified by
J-STD-020D for a small package is a peak temperature of
260 C [500 F] for 30 s.
Manual: Do not exceed 350 C [662 F] for 4 s max.
6.0 MOISTURE SEALING THE LEADS
If, in the presence of intermittent moisture or other
contaminants, there is the possibility of galvanic paths between
the leads, moisture seal the leads and exposed pads prior to
removing the protective tape.
7.0 PROTECTIVE TAPE REMOVAL
1. Use proper ESD protection.
2. Using covered fingers or tweezers to ensure that no debris
falls into the filter, sensor cover or die, grip the
overhanging front edge of the protective tape and peel it
back from the top surface of the sensor. (See Figure 1.)
3. Ensure the complete rectangle of protective tape is
removed.
Figure 1. Protective Tape Removal
Honeywell HumidIcon™ Digital
Humidity/Temperature Sensors:
SIP 4 Pin Versions of the
HIH6000 Series, HIH7000 Series,
HIH8000 Series, HIH9000 Series
Rev. B
50085524
2 Honeywell Sensing and Control
8.0 SENSOR REHYDRATION
NOTICE
SENSOR REHYDRATION
Exposure to elevated temperatures, such as those
experienced during solder reflow, may dry out the sensing
element. It is recommended that the sensor be allowed
time to rehydrate after soldering or other high
temperature/dry exposures.
Exposure to these conditions will not permanently
damage the sensor. It will generally return to its factory-
calibrated value after rehydration.
If rehydration is not performed, the sensor may read a
slight offset that slowly disappears over time as the
sensor becomes exposed to ambient conditions.
Conversely, extended exposure to condensing and high
humidity environments (>90 %RH) may cause a revisable
shift in readings which will generally return to normal after
the sensor has been allowed to dry off.
To rehydrate the sensor, expose it to room temperature under
ambient conditions (>50 %RH) for a minimum of five hours.
9.0 DIMENSIONS
Figure 2: Landing pattern.
Figure 3: Tape and reel.
Figure 2. Landing Pattern (For reference only. mm/[in].)
Figure 3. Tape and Reel Dimensions (For reference only. mm/[in])
(Note: Shown with tape cover removed.)
Honeywell HumidIcon™ Digital
Humidity/Temperature Sensors:
SIP 4 Pin Versions of the
HIH6000 Series, HIH7000 Series,
HIH8000 Series, HIH9000 Series
Rev. B
50085524
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
sensing.honeywell.com
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
The sensor’s housing does not provide electrical safety
isolation. Mount the sensor in a location where it cannot
be touched, or where a surrounding barrier prevents
human contact.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: sensing.honeywell.com
Phone and Fax:
Asia Pacific +65 6355-2828
+65 6445-3033 Fax
Europe +44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America +1-305-805-8188
+1-305-883-8257 Fax
USA/Canada +1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
P1-P3

HIH9121-021-001

Mfr. #:
Buy HIH9121-021-001
Manufacturer:
Description:
Board Mount Humidity Sensors SIP 4-Pin w/ Filter Resists Condensation
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet