4
FN6095.4
October 28, 2010
COM OFF Capacitance, C
OFF
f = 1MHz, V
NO
= V
COM
= 0V, (See Figure 6) 25 - 470 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
= V
COM
= 0V, (See Figure 6) 25 - 485 - pF
OFF-Isolation R
L
= 50Ω, C
L
= 35pF, f = 100kHz, (See Figure 4) 25 - 65 - dB
Total Harmonic Distortion (THD) f = 20Hz to 20kHz, 0.5V
P-P
, R
L
= 32Ω 25 - 0.014 - %
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 1.6 - 3.6 V
Positive Supply Current, I+ V+ = 3.6V, V
INH
, V
ADD
= 0V or V+, Switch On or Off 25 - - 0.05 µA
Full - - 1.2 µA
NOTES:
7. V
IN
= Input voltage to perform proper function.
8. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
9. r
ON
matching between channels is calculated by subtracting the channel with the highest max r
ON
value from the channel with lowest max r
ON
value.
10. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
11. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
12. Limits established by characterization and are not production tested.
Electrical Specifications: 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, V
INH
= 1V, V
INL
= 0.4V (Note 7),
Unless Otherwise Specified. Boldface limits apply over the operating temperature range,
-40°C to +85°C.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 8, 11) TYP
MAX
(Notes 8, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON-resistance, r
ON
V+ = 1.8V, I
COM
= 10.0mA, V
NO
= 1.0V,
(See Figure 5)
25 - 0.55 0.85 Ω
Full - - 0.9 Ω
r
ON
Matching Between Channels,
Δr
ON)
V+ = 1.8V, I
COM
= 10.0mA, V
NO
= 1.0V,
(See Figure 5)
25 - 0.1 - Ω
Full - 0.13 - Ω
r
ON
Flatness, R
FLAT(ON)
V+ = 1.8V, I
COM
= 10.0mA, V
NO
= 0V, 0.9V, 1.6V,
(See Figure 5)
25 - 0.14 - Ω
Full - 0.16 - Ω
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V
INH
, V
ADDH
Full 1 -- V
Input Voltage Low, V
INL
, V
ADDL
Full - - 0.4 V
Input Current, I
INH
, I
INL
, I
ADDH
,
I
ADDL
V+ = 1.8V, V
INH
, V
ADD
= 0V or V+ (Note 12) Full -0.5 - 0.5 μA
DYNAMIC CHARACTERISTICS
Inhibit Turn-ON Time, t
ON
V+ = 1.8V, V
NO
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 1, Note 12)
25 - 24 33 ns
Full - - 35 ns
Inhibit Turn-OFF Time, t
OFF
V+ = 1.8V, V
NO
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 1, Note 12)
25 - 16 25 ns
Full - - 27 ns
Address Transition Time, t
TRANS
V+ = 1.8V, V
NO
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 1, Note 12)
25 - 25 34 ns
Full - - 36 ns
Break-Before-Make Time, t
BBM
V+ = 1.8V, V
NO
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 3, Note 12)
25 - 9 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω, (See Figure 2) 25 - -20 - pC
Electrical Specifications - 3V Supply Test Conditions: V
SUPPLY
= +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 7),
Unless Otherwise Specified. Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 8, 11) TYP
MAX
(Notes 8, 11) UNITS
ISL84781
