OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

FTL4C3QE1C

P1-P3P4-P6P7-P8
FTL4C3QE1C Product Specification
Finisar Corporation October 2015 Rev. D1 Page 4
III. Absolute Maximum Ratings
Parameter
Symbol
Min
Typ
Max
Unit
Ref.
Maximum Supply Voltage
Vcc1,
VccTx,
VccRx
-0.5
3.6
V
Storage Temperature
T
S
-40
85
°C
Case Operating Temperature
T
OP
0
70
°C
Relative Humidity
RH
0
85
%
1
Damage Threshold, per Lane
DT
3.4
dBm
Notes
:
1. Non-condensing.
IV. Electrical Characteristics (T
OP
= 0 to 70
°
C, V
CC
= 3.1 to 3.47 Volts)
Parameter
Symbol
Min
Typ
Max
Unit
Ref.
Supply Voltage
Vcc1,
VccTx,
VccRx
3.1 3.47 V
Supply Current
Icc
1.13
A
Link turn-on time
Transmit turn-on time
2000
ms
2
Transmitter (per Lane)
Single ended input voltage tolerance
VinT
-0.3
4.0
V
Differential data input swing
Vin,pp
120
1200
mVpp
3
Differential input threshold
50
mV
AC common mode input voltage tolerance
(RMS)
15 mV
Differential input return loss
Per IEEE P802.3ba,
Section 86A.4.1.1
dB 4
J2 Jitter Tolerance
Jt2
0.17
UI
J9 Jitter Tolerance
Jt9
0.29
UI
Data Dependent Pulse Width Shrinkage
DDPWS
0.07
UI
Eye mask coordinates {X1, X2
Y1, Y2}
0.11, 0.31
95, 350
UI
mV
5
Receiver (per Lane)
Single-ended output voltage
-0.3
4.0
V
Differential data output swing
Vout,pp
0
800
mVpp
6
AC common mode output voltage (RMS)
7.5
mV
Termination mismatch at 1 MHx
5
%
Differential output return loss
Per IEEE P802.3ba,
Section 86A.4.2.1
dB 4
Common mode output return loss
Per IEEE P802.3ba,
Section 86A.4.2.2
dB 4
Output transition time, 20% to 80%
28
ps
J2 Jitter output
Jo2
0.42
UI
J9 Jitter output
Jo9
0.65
UI
Eye mask coordinates #1 {X1, X2
Y1, Y2}
0.29, 0.5
150, 425
UI
mV
5
Power Supply Ripple Tolerance
PSR
50
mVpp
Notes:
1. Maximum total power value is specified across the full temperature and voltage range.
FTL4C3QE1C Product Specification
Finisar Corporation October 2015 Rev. D1 Page 5
2. From power-on and end of any fault conditions.
3. After internal AC coupling. Self-biasing 100Ω differential input.
4. 10 MHz to 11.1 GHz range.
5. Hit ratio = 5 x 10E-5.
6. AC coupled with 100Ω differential output impedance.
V. Optical Characteristics (T
OP
= 0 to 70
°
C, V
CC
= 3.1 to 3.47 Volts)
Parameter
Symbol
Min
Typ
Max
Unit
Ref.
Transmitter
Signaling Speed per Lane
10.3125
GBd
1
Lane center wavelengths (range)
1264.5 – 1277.5
1284.5 – 1297.5
1304.5 – 1317.5
1324.5 – 1337.5
nm
Total Average Launch Power
P
OUT
10.3
dBm
Transmit OMA per Lane, MMF
TxOMA
-3.0
4.8
dBm
Transmit OMA per Lane, SMF
-6.0
3.5
Average Launch Power per Lane, MMF
TXP
x
-7.0
4.3
dBm 2
Average Launch Power per Lane, SMF
-10.0
2.3
Optical Extinction Ratio
ER
3.5
dB
Transmitter Dispersion Penalty, MMF
TDP
4.7
dB
Transmitter Dispersion Penalty, SMF
2.6
Transmitter OMA - TDP, MMF
TxP-TDP
-7.2
dBm 3
Transmitter OMA - TDP, SMF
-6.8
Sidemode Suppression ratio
SSR
min
30
dB
Average launch power of OFF
transmitter, per lane
-30 dBm
Relative Intensity Noise
RIN
-128
dB/Hz
4
Optical Return Loss Tolerance
20
dB
Transmitter Reflectance
-12
dB
Transmitter eye mask definition
{X1, X2, X3, Y1, Y2, Y3}
{0.25, 0.4, 0.45, 0.25, 0.28,
0.4}
Receiver
Signaling Speed per Lane
10.3125
GBd
5
Lane center wavelengths (range)
1264.5 – 1277.5
1284.5 – 1297.5
1304.5 – 1317.5
1324.5 – 1337.5
nm
Receive Power (OMA) per Lane, MMF
RxOMA
4.8
dBm
Receive Power (OMA) per Lane, SMF
3.3
Average Receive Power per Lane, MMF
RXP
x
-10.0
4.3
dBm 6,7
Average Receive Power per Lane, SMF
-13.7
2.3
Receiver Sensitivity (OMA) per Lane,
MMF
Rxsens
-10.5
dBm
Receiver Sensitivity (OMA) per Lane,
SMF
-10.5 7
Stressed Receiver Sensitivity (OMA) per
Lane, MMF
SRS
-5.0
dBm
Stressed Receiver Sensitivity (OMA) per
Lane, SMF
-8.5 6
Damage Threshold per Lane
P
MAX
5.5
dBm
FTL4C3QE1C Product Specification
Finisar Corporation October 2015 Rev. D1 Page 6
Return Loss
RL
-20
dB
Vertical eye closure penalty, per lane
3.6
dB
Receive electrical 3 dB upper cutoff
frequency, per lane
12.3
GHz
LOS De-Assert
LOS
D
-12
dBm
7
LOS Assert
LOS
A
-28
dBm
7
LOS Hysteresis
1
dB
Notes
:
1. Transmitter consists of 4 lasers operating at 10.3Gb/s each.
2. Minimum value is informative.
3. Even if TDP < 0.5 dB (MMF) or TDP < 0.8 dB (SMF), TxP – TDP must be geater than this value.
4. RIN is scaled by 10*log(10/4) to maintain SNR outside of transmitter.
5. Receiver consists of 4 photodetectors operating at 10.3Gb/s each.
6. Minimum value is informative, equals min TxOMA with infinite ER and max channel insertion loss.
7. SMF receiver sensitivity guaranteed by design, but nots measured in production.
8. LOS Assert and De-Assert values are informative and may vary between MMF and SMF uses.
VI. Memory Map and Control Registers
Compatible with SFF-8636
2
. Please see Finisar Application Note AN-2104
6
for memory
map details.
Although this module is designed for both multimode and single mode fiber operation, the
Tx and Rx power monitors are calibrated for multimode fiber. Therefore, the DDM reading
should be relied upon only for multimode operation.
VII. Environmental Specifications
Finisar FTL4C3QE1C transceivers have an operating temperature range from 0°C to +70°C
case temperature.
Environmental Specifications Symbol Min Typ Max Units Ref.
Case Operating Temperature
T
op
0
70
°C
Storage Temperature
T
sto
-40
85
°C
VIII. Regulatory Compliance
Finisar FTL4C3QE1C transceivers are RoHS-6 Compliant. Copies of certificates are
available at Finisar Corporation upon request.
FTL4C3QE1C transceiver modules are Class 1 laser eye safety compliant per IEC 60825-1.
P1-P3P4-P6P7-P8

FTL4C3QE1C

Mfr. #:
Buy FTL4C3QE1C
Manufacturer:
Finisar Corporation
Description:
Fiber Optic Transmitters, Receivers, Transceivers XCVR, QSFP, 140m on OM3 / 160m on OM4 / 1km on SMF, 40GE over MMF & SMF, 4x10G LM4 UNIV CWDM DFB, PIN, Limiting, XLPPI electrical interface, RoHS,
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet