NCV7380
http://onsemi.com
3
Electrical Specification
All voltages are referenced to ground (GND). Positive
currents flow into the IC.
The maximum ratings given in the table below are
limiting values that do not lead to a permanent damage of
the device but exceeding any of these limits may do so.
Long term exposure to limiting values may effect the
reliability of the device.
OPERATING CONDITIONS
Characteristic Symbol Min Max Unit
Battery Supply Voltage (Note 1) V
S
7.0 18 V
Supply Voltage V
CC
4.5 5.5 V
Operating Ambient Temperature T
A
−40 +125 °C
MAXIMUM RATINGS
Rating Symbol Condition Min Max Unit
Battery Supply Voltage V
S
t < 1 min
−0.3
30 V
Load Dump, t < 500 ms 40
Supply Voltage V
CC
− −0.3 +7.0 V
Transient Supply Voltage V
S.tr1
ISO 7637/1 Pulse 1 (Note 2) −150 − V
Transient Supply Voltage V
S..tr2
ISO 7637/1 Pulses 2 (Note 2) − 100 V
Transient Supply Voltage V
S..tr3
ISO 7637/1 Pulses 3A, 3B −150 150 V
BUS Voltage V
BUS
t < 500 ms , Vs = 18 V −27
40
V
t < 500 ms ,Vs = 0 V −40
Transient Bus Voltage V
BUS..tr1
ISO 7637/1 Pulse 1 (Note 3) −150 − V
Transient Bus Voltage V
BUS.tr2
ISO 7637/1 Pulses 2 (Note 3) − 100 V
Transient Bus Voltage V
BUS.tr3
ISO 7637/1 Pulses 3A, 3B (Note 3) −150 150 V
DC Voltage on Pins TxD, RxD V
DC
− −0.3 7.0 V
ESD Capability, Charged Device Model V
ESDCDM
(Note 4) −1.0 1.0 kV
ESD Capability of RxD, TxD, V
CC
, BUS Pins
ESD Capability of V
S
Pin
V
ESDHBM
Human body model, equivalent to
discharge 100 pF with 1.5 k (Note 4)
−2.0
−1.5
2.0
1.5
kV
kV
Maximum Latchup Free Current at Any Pin I
LATCH
− −500 500 mA
Maximum Power Dissipation P
tot
At T
A
= 125°C − 197 mW
Thermal Impedance
JA
In Free Air − 152 °C/W
Storage Temperature T
stg
− −55 +150 °C
Junction Temperature T
J
− −40 +150 °C
LEAD TEMPERATURE SOLDERING REFLOW
Lead Free, 60 sec −150 sec above 217, 40 sec Max at Peak T
SLD
− 265 Peak °C
Leaded, 60 sec −150 sec above 183, 30 sec Max at Peak T
SLD
− 240 Peak °C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. V
S
is the IC supply voltage including voltage drop of reverse battery protection diode, V
DROP
= 0.4 to 1.0 V, V
BAT_ECU
voltage range is
7.0 to 18 V.
2. ISO 7637 test pulses are applied to V
S
via a reverse polarity diode and > 2.0 F blocking capacitor.
3. ISO 7637 test pulses are applied to BUS via a coupling capacitance of 1.0 nF.
4. This device incorporates ESD protection and is tested by the following methods:
ESD HBM tested per AEC−Q100−002 (EIA/JESD22−A 114C)
ESD CDM tested per EIA/JESD22−C 101C, Field Induced Model.