101
021717
TPM Multianode
Tantalum Ultra Low ESR Capacitor
RATINGS & PART NUMBER REFERENCE
Rated Rated Category Category DCL DF
ESR
100kHz RMS Current (A)
AVX Case Capacitance
Voltage Temperature Voltage Temperature Max. Max.
Max.
MSL
Part No. Size (μF)
(V) (ºC) (V) (ºC) (μA) (%)
@ 100kHz
25ºC 85ºC 125ºC
(mΩ)
TPME476*035#0055 E 47 35 85 23 125 16 6 55 3 2.216 1.994 0.886
TPME476*035#0065 E 47 35 85 23 125 16 6 65 3 2.038 1.834 0.815
50 Volt @ 85°C
TPMD106*050#0140 D 10 50 85 33 125 5 8 140 3 1.350 1.215 0.540
TPME106*050#0120 E 10 50 85 33 125 5 6 120 3 1.500 1.350 0.600
TPME156*050#0075 E 15 50 85 33 125 7.5 6 75 3 1.897 1.708 0.759
TPME156*050#0100 E 15 50 85 33 125 7.5 6 100 3 1.643 1.479 0.657
TPME226*050#0075 E 22 50 85 33 125 11 8 75 3 1.897 1.708 0.759
TPME226*050#0100 E 22 50 85 33 125 11 8 100 3 1.643 1.479 0.657
Moisture Sensitivity Level (MSL) is defined according to J-STD-020
All technical data relates to an ambient temperature of +25°C. Capacitance and DF are measured at 120Hz, 0.5V RMS with a maximum DC bias of 2.2 volts.
DCL is measured at rated voltage after 5 minutes.
The EIA & CECC standards for low ESR Solid Tantalum Capacitors allow an ESR movement to 1.25 times catalogue limit post mounting.
For typical weight and composition see page 223.
NOTE: AVX reserves the right to supply a higher voltage rating or tighter tolerance part in the same case size, to the same reliability standards.
TEST
TPM series (Temperature range -55ºC to +125ºC)
Condition Characteristics
Visual examination no visible damage
DCL initial limit
Endurance ΔC/C within ±10% of initial value
DF initial limit
ESR 1.25 x initial limit
Visual examination no visible damage
DCL 1.5 x initial limit
Humidity ΔC/C within ±10% of initial value
DF 1.2 x initial limit
ESR 1.25 x initial limit
+20ºC -55ºC +20ºC +85ºC +125ºC +20ºC
Temperature DCL
IL* n/a IL* 10 x IL* 12.5 x IL* IL*
Stability ΔC/C
n/a +0/-10% ±5% +10/-0% +12/-0% ±5%
DF
IL* 1.5 x IL* IL* 1.5 x IL* 2 x IL* IL*
ESR
1.25 x IL* 2.5 x IL* 1.25 x IL* 1.25 x IL* 1.25 x IL* 1.25 x IL*
Visual examination no visible damage
Surge DCL initial limit
Voltage
ΔC/C within ±5% of initial value
DF initial limit
ESR 1.25 x initial limit
Determine after application of rated voltage for 2000
+48/-0 hours at 85±2ºC and then leaving 1-2 hours at
room temperature. Also determine of 125ºC tempera-
ture, category voltage for 2000 +48/-0 hours and
then leaving 1-2 hours at room temperature. Power
supply impedance to be ≤0.1Ω/V.
Determine after storage without applied voltage
at 65±2ºC and 95±2% relative humidity for 500
hours and then recovery 1-2 hours at room
temperature.
Test temperature: 125ºC+3/0ºC
Test voltage: Category voltage at 125ºC
Surge voltage: 1.3 x category voltage at 125ºC
Series protection resistance 1000±100Ω
Discharge resistance: 1000Ω
Number of cycles: 1000x
Cycle duration: 6 min; 30 sec charge,
5 min 30 sec discharge
Step Temperature°C Duration(min)
1 +20±2 15
2 -55+0/-3 15
3 +20±2 15
4 +85+3/-0 15
5 +125+3/-0 15
6 +20±2 15
*Initial Limit
QUALIFICATION TABLE
