2
Technical Data 4085
Effective March 2016
HCM0703
High current power inductors
www.eaton.com/elx
Product Specifications
Part Number
6
OCL
1
(μH) ±20%
FLL
2
(μH)
minimum
I
rms
3
(A )
I
sat
4
(A )
DCR (mΩ)
typical @ 20 °C
DCR (mΩ)
maximum @ 20 °C K-factor
5
HCM0703-R15-R 0.15 0.09 26 52 1.9 2.5 1044
HCM0703-R22-R 0.22 0.13 23 40 2.5 2.8 986
HCM0703-R47-R 0.47 0.28 17.5 26 4.0 4.2 580
HCM0703-R68-R 0.68 0.41 15.5 25 5.0 5.5 455
HCM0703-R82-R 0.82 0.49 13 24 6.7 8.0 439
HCM0703- 1R0-R 1.0 0.60 11 22 9.0 10 374
HCM0703- 1R5-R 1.5 0.90 9.0 18 14 15 366
HCM0703- 2R2-R 2.2 1.3 8.0 14 18 20 281
HCM0703- 3R3-R 3.3 2.0 6.0 13.5 28 30 252
HCM0703- 4R7-R 4.7 2.8 5.5 10 37 40 210
HCM0703- 6R8-R 7 4.1 4.5 8.0 54 60 151
HCM0703- 8R2-R 8 4.9 4.0 7.5 64 68 142
HCM0703- 100-R 10 6.0 3.2 7.0 71 78 132
HCM0703- 150-R 14.9±15% 10.1 2.2 5.0 113 127 105
HCM0703- 220-R 22 14.1 2.3 3.0 135 149 83
HCM0703- 330-R 33 19.8 1.8 2.2 220
242 76
1. Open Circuit Inductance (OCL) Test Parameters: 100 kHz, 0.25 V
rms
, 0.0 Adc, +25°C.
2. Full Load Inductance (FLL) Test Parameters: 100 kHz, 0.25 V
rms
, I
sat
, @ +25 °C.
3. I
rms
: DC current for an approximate temperature rise of 40 °C without core loss. Derating is necessary for AC currents.
PCB layout, trace thickness and width, air-flow, and proximity of other heat generating components will affect the
temperature rise. It is recommended that the temperature of the part not exceed 125 °C under worst case operating
conditions verified in the end application.
4. I
sat
: Peak current for approximately 20% rolloff at +25 °C.
5. K-factor: Used to determine B
p-p
for core loss (see graph). Bp-p = K * L * ΔI. B
p-p
: (Gauss), K: (K-factor from table), L:
(Inductance in μH), ΔI (Peak to peak ripple current in Amps).
6. Part Number Definition: HCM0703-xxx-R
HCM0703 = Product code and size
-xxx= Inductance value in μH, R = decimal point,
if no R is present then last character equals number of zeros.
“-R” suffix = RoHS compliant
Dimensions (mm)
Part marking: XXX=Inductance value in uH, R= decimal point. If no R is present then last character equals number of zeros.
wly=date code, R=revision level
All soldering surfaces to be coplanar within 0.10 millimeters
Tolerances are ±0.3 millimeters unless stated otherwise
Color: Grey