ADG721/ADG722/ADG723 Data Sheet
Rev. E | Page 4 of 16
V
DD
= 3 V ± 10%, GND = 0 V. All specifications −40°C to +85°C, unless otherwise noted.
Table 2.
A, B Grades
1
Parameter
+25°C
40°C to +85°C
Unit
ANALOG SWITCH
Analog Signal Range
0 to V
DD
V
On Resistance, R
ON
6.5 Ω typ V
S
= 0 V to V
DD
, I
S
= −10 mA
10 Ω max See Figure 12
On Resistance Match Between Channels, ∆R
ON
0.3 Ω typ V
S
= 0 V to V
DD
, I
S
= −10 mA
1.0 Ω max
On Resistance Flatness, R
FL AT(ON)
3.5 Ω typ V
S
= 0 V to V
DD
, I
S
= −10 mA
LEAKAGE CURRENTS A Grade V
DD
= 3.3 V
Source off Leakage, I
S
(OFF) ±0.01 nA typ V
S
= 3 V/1 V, V
D
= 1 V/3 V, see Figure 13
Drain off Leakage, I
D
(OFF) ±0.01 nA typ V
S
= 3 V/1 V, V
D
= 1 V/3 V, see Figure 13
Channel on Leakage, I
D
, I
S
(ON) ±0.01 nA typ V
S
= V
D
= 1 V or 3 V, Figure 14
LEAKAGE CURRENTS B Grade
DD
Source off Leakage, I
S
(OFF)
±0.01
nA typ
S
D
±0.25 ±0.35 nA max See Figure 13
Drain off Leakage, I
D
(OFF) ±0.01 nA typ V
S
= 3 V/1 V, V
D
= 1 V/3 V
±0.25 ±0.35 nA max See Figure 13
Channel on Leakage, I
D
, I
S
(ON) ±0.01 nA typ V
S
= V
D
= 1 V or 3 V
±0.25 ±0.35 nA max See Figure 14
DIGITAL INPUTS
Input High Voltage, V
INH
2.0 V min
Input Low Voltage, V
INL
0.4 V max
Input Current
I
INL
or I
INH
0.005 μA typ V
IN
= V
INL
or V
INH
±0.1 μA max
DYNAMIC CHARACTERISTICS
2
t
ON
16 ns typ R
L
= 300 Ω, C
L
= 35 pF
24 ns max V
S
= 2 V, see Figure 15
t
OFF
7 ns typ R
L
= 300 Ω, C
L
= 35 pF
11 ns max V
S
= 2 V, see Figure 15
Break-Before-Make Time Delay, t
D
(ADG723 Only) 7 ns typ R
L
= 300 Ω, C
L
= 35 pF
1 ns min V
S1
= V
S2
= 2 V, see Figure 16
Charge Injection 2 pC typ V
S
= 1.5 V, R
S
= 0 Ω, C
L
= 1 nF, see Figure 17
Off Isolation −60 dB typ R
L
= 50 Ω, C
L
= 5 pF, f = 10 MHz
−80 dB typ R
L
= 50 Ω, C
L
= 5 pF, f = 1 MHz, see Figure 18
Channel-to-Channel Crosstalk −77 dB typ R
L
= 50 Ω, C
L
= 5 pF, f = 10 MHz
−97 dB typ R
L
= 50 Ω, C
L
= 5 pF, f = 1 MHz, see Figure 19
Bandwidth −3 dB 200 MHz typ R
L
= 50 Ω, C
L
= 5 pF, see Figure 20
C
S
(OFF) 7 pF typ
C
D
(OFF) 7 pF typ
C
D
, C
S
(ON)
18
pF typ
POWER REQUIREMENTS V
DD
= 3.3 V
I
DD
0.001 μA typ Digital inputs = 0 V or 3 V
1.0 μA max
1
Temperature range: A, B Grades, −40°C to +85°C. All specifications apply to both grades unless otherwise stated.
2
Guaranteed by design; not subject to production test.
Data Sheet ADG721/ADG722/ADG723
Rev. E | Page 5 of 16
ABSOLUTE MAXIMUM RATINGS
T
A
= 25°C unless otherwise noted.
Table 3.
Parameter Rating
V
DD
to GND −0.3 V to +7 V
Analog, Digital Inputs
1
−0.3 V to V
DD
+ 0.3 V or 30 mA,
whichever occurs first
Continuous Current, S or D 30 mA
Operating Temperature Range
Industrial (A, B Grade) −40°C to +85°C
Storage Temperature Range
−65°C to +150°C
Junction Temperature +150°C
8-Lead MSOP
θ
JA
Thermal Impedance 206°C/W
θ
JC
Thermal Impedance 44°C/W
8-Lead LFCSP (4-Layer Board)
θ
JA
Thermal Impedance
1
50.8°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) 215°C
Infrared (15 sec) 220°C
Lead-Free Temperature,
Soldering
IR Reflow, Peak Temperature 260°C (+0/−5°C)
Time at Peak Temperature 10 sec to 40 sec
ESD 2 kV
1
Assumes exposed paddle is tied to ground.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ADG721/ADG722/ADG723 Data Sheet
Rev. E | Page 6 of 16
PIN CONFIGURATION AND PIN DESCRIPTIONS
8
7
6
5
1
2
3
4
S1
D1
IN2
GND
IN1
D2
S2
V
DD
ADG721/
ADG722/
ADG723
TOP VIEW
(Not to Scale)
00045-004
NOTES
1. EXPOSED PADDLE OF LFCSP
SHOULD BE TIED TO GROUND.
Figure 4. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. Mnemonic Descriptions
1 S1 Source Pin 1. May be an input or an output.
2
D1
Drain Pin 1. May be an input or an output.
3 IN2
Logic Control Input for Switch S2D2.
4 GND Ground (0 V) Reference.
5 S2 Source Pin 2. May be an input or an output.
6 D2 Drain Pin 2. May be an input or an output.
7 IN1
Logic Control Input for Switch S1
D1.
8 V
DD
Positive Power Supply Input.
Table 5. Truth Table (ADG721/ADG722)
ADG721 In
ADG722 In
Switch Condition
0 1 Off
1 0 On
Table 6. Truth Table (ADG723)
Logic
Switch 1
Switch 2
0 Off On
1 On Off

ADG723ACPZ-REEL7

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Analog Switch ICs 4 Ohm 1.8V CMOS Dual SPST
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union