Users should evaluate the suitability of this product for their application. Specifi cations are subject to change without notice.
Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specifi cation, without notifi cation to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”). OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 1
Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL.
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2012-2013 Tyco Electronics Corporation. All rights reserved.
SPECIFICATION CONTROL DRAWING
82/1132
THREE CONDUCTOR CABLE, SHIELDED, JACKETED, OUTER SPACE, FLEXIBLE, 600 VOLT 11-13-13 B
This specifi cation sheet forms a part of the latest issue of Raychem Specifi cation 80.
JACKET - LOW OUTGASSING,
RADIATION-CROSSLINKED,
MODIFIED FLEXIBLE ETFE
COMPONENT WIRES - 82/0112
TITLE
Date
Revision
SHIELD - SILVER-COATED COPPER
CABLE CONSTRUCTION DETAILS
PART NUMBER
1/
CONDUCTOR
SIZE
(AWG)
SHIELD
SIZE
(AWG)
JACKET THICKNESS
(inch)
OUTSIDE DIAMETER
(inch)
MAXIMUM
WEIGHT
(lbs/1000 ft.)
MINIMUM NOMINAL NOMINAL MAXIMUM
82/1132-28-* 28 38 .006 .008 .096 .101 9.1
82/1132-26-* 26 38 .006 .009 .106 .112 10.6
82/1132-24-* 24 38 .006 .009 .115 .121 13.4
82/1132-22-* 22 38 .006 .009 .128 .134 16.8
82/1132-20-* 20 38 .007 .010 .151 .159 22.8
82/1132-18-* 18 38 .008 .011 .177 .186 32.8
82/1132-16-* 16 38 .009 .013 .214 .224 47.3
82/1132-14-* 14 38 .010 .014 .259 .272 71.1
82/1132-12-* 12 38 .011 .016 .310 .326 103.
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CROSSLINKING PROOF TEST: 300 ± 3°C for 1 hour
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 100% (minimum)
Tensile Strength, 3000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1500 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
RADIATION RESISTANCE (Test per Raychem Spec 55/):
500 megarads
NOTE: Nominal values are for information only.
Nominal values are not requirements.
SECANT MODULUS (Test per ASTM D 882):
4.0 x 10
4
lbf/in
2
(maximum),
2% strain, 2 inch jaw separation, 0.2 inch/minute
SHIELD COVERAGE: 85% (minimum)
VACUUM STABILITY (Test per ASTM E 595):
Total Mass Loss (TML), 1.00% (maximum)
Volatile Condensable Material (VCM), 0.10% (maximum)
VOLTAGE WITHSTAND (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
1/ PART NUMBER:
The “*” in the part numbers above shall be replaced by color code
designators with a slash separating the component wire colors and a
dash separating the component wire colors from the jacket color.
Colors shown do not necessarily refl ect the sequence of manufacturing.
Example: AWG 24, black, brown and red component wires;
white jacket: 82/1132-24-0/1/2-9
