Specifications
Drawing
Marking
Standard rating
Item Performance Characteristics
Category Temperature Range
Capacitance Tolerance
Dissipation Factor (at 120Hz)
ESR (100kHz)
Leakage Current
Ripple Current
Damp Heat
(No voltage applied)
Temperature Cycles
Resistance
to Soldering Heat
Surge
Endurance 1
Endurance 2
Shear Test
Terminal Strength
–55 to +105˚C (Rated temperature + 85˚C)
±20% (120Hz)
Refer to the list below
Refer to the list below
After 5 minute's application of rated voltage, leakage current
at 20˚C is not more than 0.1CV
Type numbering system (Example : 6.3V 10µF)
F38
J0 1
0 6
M
M A
123
546
78
91011
Rated Capacitance
Capacitance tolerance
Case code
Rated voltage
Series
Tape width
(mm)
Reel Dia
(φ180mm)
8
A
Taping code
At 60˚C, 90 to 95% R.H. 500hours
–55˚C / +105˚C 30 minutes each 5 cycle
Test Condition ; 10 second reflow at 240˚C
Capacitance Change Within –20 to +30% of initial value
Dissipation Factor
......
1.5 times initial specified value or less
Leakage Current
........
Initial specified value or less
Capacitance Change Within ±20% of initial value
Dissipation Factor
......
Initial specified value or less
Leakage Current
........
Initial specified value or less
Capacitance Change Within ±20% of initial value
Dissipation Factor
......
1.3 times initial specified value or less
Leakage Current
........
Initial specified value or less
After application of surge voltage in series with a 1kΩ resistor
at the rate of 30 seconds ON, 30 seconds OFF, for 1000
sucessive test cycles at 85˚C, capacitors meet the
characteristics requirements listed below.
Capacitance Change
...
Within ±20% of initial value
Dissipation Factor
........
Initial specified value or less
Leakage Current
..........
Initial specified value or less
After 1000 hours' application of rated voltage in series
with a 3Ω resistor at 85˚C.
Capacitance Change
....
Within ±20% of initial value
Dissipation Factor
...
1.5 times initial specified value or less
Leakage Current
...
Initial specified value or less
After 1000 hours' application of derated voltage in series
with a 3Ω resistor at 105˚C,capacitors meet the characteristic
requirements listed below
Capacitance Change
....
Within ±20% of initial value
Dissipation Factor
...
3 times initial specified value or less
Leakage Current
...
Initial specified value or less
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has
no electrode and has been soldered beforehand on an
aluminum substrate, there shall be found
neither exfoliation nor its sign at the
terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with a specified jig at the
center of the substrate so that the substrate may bend by
1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
Refer to the list below
5N (0.51kg
•
f)
For 10±1 seconds
20
R230
45 45
1
mm
M Case
Rated voltage
(Voltage code)
J
S Case
Rated voltage
(Voltage code)
Capacitance code
Jn
L
H
W1
W2
S1S2S1
(mm)
Case code
LW
1 S2W2 HS1
M 1.6±0.1 0.85±0.1 0.65±0.1 0.8±0.1 0.5±0.1 0.6±0.1
S 2.0±0.1 1.25±0.1 0.9±0.1 0.8±0.1 0.5±0.1 1.0±0.1
Standard ratings
( )
The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
Cap.(
F)
Code
V
4.7
10
22
33
47
475
106
226
336
476
4
0G
M
M
S
S
6.3
0J
M
M
•
S
S
(S)
10
1A
M
M
•
S
(S)
S
a
n
s
Capacitance
code
µ
Rated Volt
(
V
)
Rated Capacitance
Leakage Current
Disspation Factor
(%@120Hz)
ESR
(mΩ@100kHz)
Rated Ripple
(mArms@100kHz)
Case
code
4
6.3
10
10
22
33
47
10
22
22
33
4.7
10
10
M
M
S
S
M
M
S
S
M
M
S
4.0
8.8
13.2
18.8
6.3
13.9
13.9
20.8
4.7
10.0
10.0
6
6
6
6
6
6
6
6
6
6
6
200
200
200
200
200
200
200
200
200
200
200
350
350
450
450
350
350
450
450
350
350
450
Part Number
F380G106MMA
F380G226MMA
F380G336MSA
F380G476MSA
F380J 106MMA
F380J 226MSA
F380J 226MMA
F380J 336MSA
F381A475MMA
F381A106MMA
F381A106MSA
