OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

NFM18PC225B0J3D

P1-P3P4-P6P7-P9P10-P10
NFM18PC225B0J3_ (0603, 2.2uF, DC6.3V)
_: packaging code Reference Sheet
1.Scope
　　
2.MURATA Part NO. System
(Ex.)
3. Type & Dimensions
a)Equivalent Circuit
(Unit:mm)
4.Rated value
5.Package
Product specifications in this catalog are as of Mar.3,2016,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
Insulation
Resistance
mark
Packaging Unit
(7) Packaging
This product specification is applied to Chip EMIFIL®Chip 3-terminal Capacitor for Large Current used for General Electronic equipment.
(3) Nominal
Capacitance
Capacitance
Tolerance
(5)
DC Rated
Voltage
Rated
Current
(mA)
j
0.2±0.1
Chip EMIFIL®Chip 3-terminal Capacitor for Large Current for General
Specifications and Test Methods
(Operating /Storage Temp. Range)
-40 to 85 °C / -40 to 85 °C
±20 %
2A(DC)
20mΩmax.
2.2 uF
DC
Resistance
200MΩmin.
DC 6.3 V
(1)-2 W
T
e
g
D
f180mm Reel
PAPER W8P4
4000 pcs./Reel
0.8±0.1
0.6±0.1
0.25±0.1
0.2 min.
(1)L/W
Dimensions
(2)Features
(3)Nominal
Capacitance
(4)Temperature
Characteristics
(5)DC Rated
Voltage
(6)Electrode
(7)Packaging
Code
NFM 18 PC 225 B 0J 3 D
NFM18PC225B0J3-01 1
Electrical Performance
No Specification Test Method
1 Capacitance Shown in Rated value.
Frequency : 1.0±0.1kHz
(Cap.)
Voltage :
Only NFM18PC225B0J3 : 0.5±0.1V(rms)
Except above : 1±0.2V(rms)
2
Voltage : Rated Voltage
Time : 2 minutes max.
3 DC Resistance Measured with 100mA max.
4 Withstanding Voltage Products shall not be damaged.
Test Voltage : Rated Voltage x 300%
Time : 1 to 5 s
Charge Current : 50 mA max.
5
Operating Temperature
Shown in Rated value. Includes self-heating
6
Storage Temperature
Standard Testing Condition
< Unless otherwise specified >
< In case of doubt >
Temperature : Ordinary Temp. / 15 °C to 35 °C Temperature: 20 °C ± 2 °C
Humidity: Ordinary Humidity / 25 %(RH) to 85 %(RH)
Humidity: 60 %(RH) to 70 %(RH)
Atmospheric pressure: 86 kPa to 106 kPa
■SPECIFICATIONS AND TEST METHODS
Item
Insulation
Resistance(I.R.)
JEMCPS-02211C 2
Mechanical Performance
No Specification Test Method
1 Appearance and
Appearance:No defects or abnormalities. Appearance:Visual inspection.
Dimensions
Dimensions:Within the specified dimensions. Dimensions:Using calipers.
2 Solderability Flux : Ethanol solution of rosin, 25(wt)%
Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 240 ± 3°C
Immersion Time : 3±1 s
Immersion and emersion rates : 25mm / s
3 Resistance to
Meet Table 1. Flux : Ethanol solution of rosin, 25(wt)%
soldering heat
Table 1 Pre-heat : 150±10°C, 60 to 90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 270 ± 5°C
Immersion Time : 10 ± 1 s
Immersion and emersion rates : 25mm / s
Initial values :
measured after heat treatment (150+0 / -10 °C,1hour) and
exposure in the room condition for 48±4 hours.
Then measured after exposure in the room condition for 48±
4 hours.
4 Bending Strength
Meet Table 2. It shall be soldered on the glass-epoxy substrate
(100×40×1.0mm).
Table 2 Deflection : 2 mm
Keeping Time : 30 s
(in mm)
5 Drop
It shall be dropped on concrete or steel board.
Height : 1m
Method : Free fall
Attitude from which the product is dropped : 3 directions
6 Bonding Strength
It shall be soldered on the glass-epoxy substrate.
Applying Force (F) : 9.8 N
Applying Time : 10 s
(in mm)
7 Vibration Meet Table 3.
It shall be soldered on the glass-epoxy substrate.
Table 3 Oscillation Frequency : 10 to 2000 to 10Hz for 20 minute.
Total amplitude 1.5 mm or Acceleration amplitude 196m/s2
whichever is smaller.
Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
Preconditioning : Heat treatment (150+0 / -10 °C,1hour)
■SPECIFICATIONS AND TEST METHODS
Item
The electrodes shall be no failure after tested.
Products shall be no failure after tested.
Electrodes shall be at least 90% covered with
new solder coating.
The Number of Time : 3 times for each direction
(Total 9 times)
0.4
0.6
1.6
0.5
Appearance
No damaged
Cap. Change
Within ±7.5%
DC
Resistance
0.05max.
Appearance
No damaged
Cap. Change
Within ±7.5%
I.R.
Meet the initial rated
value.
DC
Resistance
0.05 max.
Appearance
No damaged
Capacitance
Meet the initial rated
value.
DC
Resistance
0.05max.
45
R340
F
Deflection
45
Product
Pressure jig
JEMCPS-02211C 3
P1-P3P4-P6P7-P9P10-P10

NFM18PC225B0J3D

Mfr. #:
Buy NFM18PC225B0J3D
Manufacturer:
Description:
Feed Through Capacitors 2.2uF 20% 6.3Volts
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet