DO NOT
SCALE FROM
THIS PRINT
SIB-1XX-XX-XX-S-XX-XX
No OF POSITIONS
-02 THRU -30
(PER ROW)
ROW SPECIFICATION
LEAD STYLE
-02: SURFACE MOUNT
(USE C-228-X)
PLATING SPECIFICATION
-F: FLASH SELECTIVE
(USE C-228-F)
-FM: FLASH SELECTIVE, PURE TIN,
MATTE FINISH
(USE C-228-F)
THREADED INSERT OPTION
[NOT AVAILABLE ON 30 POS]
-E: TI-2-56-115 (ENGLISH)
-M: TI-M2-4-115-N (METRIC)
(SEE FIG. 2, SHEET 2)
-TI: NO INSERTS PLACED IN BODY
(SEE TABLE 1 ON SHEET 2 FOR
-TI POSITIONAL OFFERINGS)
OPTION
-LC: LOCKING CLIPS
(USE LC-09-TM)(SEE NOTE 13)
[N/A WITH THREADED INSERT OPTION
-E, -M OR -TI]
AVAILABLE TO EXISTING CUSTOMERS ONLY
*
*
*
*
-S: SINGLE (USE SIBC-XX-02-S)
X
.150
REF
3.810
.207
±.005
5.267
±0.127
(No OF POSITIONS -2) x .100[2.54] REF
(No OF POSITIONS -1) x .100(2.54) REF
.045 1.143
"A"
"A"
LC-09-TM
C-228-X
C
.015
REF
0.38
.335 8.509
REF
.0287
MIN END
0.729
WALL ON CUT PART
.264
REF
6.706
No OF POSITIONS x .100[2.54]
((No OF POSITIONS -1) x .100[2.54])
.005[.13]
.050 1.27
REF
SIBC-XX-02-S
.015[.38]
.005[.13]
01
C
FIG 1
SIB-120-02-X-S-LC SHOWN
.0560
REF
1.422
.071
±.003
1.803
±0.08
.044
REF
1.13
.175
REF
4.45
.203 5.16
'A'
SECTION "A"-"A"
C
.0033
-
.0020
+
.0040
0.084
-
0.051
+
0.102
(SEE NOTES 9 & 10)
DETAIL 'A'
SCALE 10 : 1
C
C
C
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
.100 SINGLE INTERFACE BEAM ASSEMBLY
BY:
SIB-1XX-XX-XX-S-XX-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
DEAN P
9/20/2000
2
1
SHEET SCALE: 2:1
INSULATOR: LCP, COLOR: BLACK
CONTACT: PHOSPHOR BRONZE
F:\DWG\MISC\MKTG\SIB-1XX-XX-XX-S-XX-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY: SEE TABLE 2.
3. BURR ALLOWANCE: .0015[.038] MAX.
4. MAXIMUM CUT FLASH: .010[.3], CAN NOT EXTEND PAST TAIL.
5. MINIMUM PUSHOUT FORCE: 1 LB.
6. MAXIMUM ALLOWABLE BOW: .004[.10] INCH/INCH AFTER ASSEMBLY.
7. THREADED INSERT MUST HANDLE 25 IN-OZ OF TORQUE WITHOUT
ROTATING OR LOOSENING.
8. THREADED INSERT RETENTION: 10 LBS. MINIMUM.
9. MAX VARATION FROM PIN TO PIN TO BE .002.
10. MEASURED ON UNCUT PARTS.
11. NOTE DELETED.
12. NOTE DELETED.
13.
DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION X
