LT1011/LT1011A
4
1011afe
For more information www.linear.com/LT1011
elecTrical characTerisTics
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Inputs may be clamped to supplies with diodes so that
maximum input voltage actually exceeds supply voltage by one diode
drop. See Input Protection in the Applications Information section.
Note 3: T
JMAX
= 150°C.
Note 4: Output is sinking 1.5mA with V
OUT
= 0V.
Note 5: These specifications apply for all supply voltages from a single
5V to ±15V, the entire input voltage range, and for both high and low
output states. The high state is I
SINK
= 100µA, V
OUT
= (V
+
– 1V) and
the low state is I
SINK
= 8mA, V
OUT
= 0.8V. Therefore, this specification
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
S
= ±15V, V
CM
= 0V, R
S
= 0Ω, V
GND
= –15V, output at pin 7 unless
otherwise noted.
SYMBOL PARAMETER CONDITIONS
LT1011AC/AI/AM LT1011C/I/M
UNITSMIN TYP MAX MIN TYP MAX
V
OS
Input Offset Voltage (Note 4)
●
0.3 0.5
1
0.6 1.5
3
mV
mV
*Input Offset Voltage R
S
≤ 50k (Note 5)
●
0.75
1.5
2
3
mV
mV
I
OS
*Input Offset Current (Note 5)
●
0.2 3
5
0.2 4
6
nA
nA
I
B
Input Bias Current (Note 4) 15 25 20 50 nA
*Input Bias Current (Note 5)
●
20 35
50
25 65
80
nA
nA
∆V
OS
∆T
Input Offset Voltage Drift
(Note 6)
T
MIN
≤ T ≤ T
MAX
●
4 15 4 25 µV/°C
A
VOL
*Large-Signal Voltage Gain R
L
= 1k Connected to 15V,
–10V ≤ V
OUT
≤ 14.5V
200 500 200 500 V/mV
R
L
= 500Ω Connected to 5V,
V
S
= Single 5V, V
GND
= 0V,
0.5V ≤ V
OUT
≤ 4.5V
50 300 50 300 V/mV
CMRR Common Mode Rejection Ratio 94 115 90 115 dB
*Input Voltage Range (Note 9) V
S
= ±15V
V
S
= Single 5V
●
●
–14.5
0.5
13
3
–14.5
0.5
13
3
V
V
t
D
*Response Time (Note 7) 150 250 150 250 ns
V
OL
*Output Saturation Voltage,
V
GND
= 0
V
IN
= –5mV, I
SINK
= 8mA, T
J
≤ 100°C
V
IN
= –5mV, I
SINK
= 8mA
V
IN
= –5mV, I
SINK
= 50mA
●
●
0.25
0.25
0.7
0.4
0.45
1.5
0.25
0.25
0.7
0.4
0.45
1.5
V
V
V
*Output Leakage Current V
IN
= 5mV, V
GND
= –15V,
V
OUT
= 20V
●
0.2 10
500
0.2 10
500
nA
nA
*Positive Supply Current V
GND
= 0 3.2 4 3.2 4 mA
*Negative Supply Current V
GND
= 0 1.7 2.5 1.7 2.5 mA
*Strobe Current (Note 8) Minimum to Ensure Output Transistor is Off,
V
GND
= 0
500 500 µA
Input Capacitance 6 6 pF
*Indicates parameters which are guaranteed for all supply voltages, including a single 5V supply. See Note 5.
defines a worst-case error band that includes effects due to common
mode signals, voltage gain and output load.
Note 6: Drift is calculated by dividing the offset voltage difference
measured at min and max temperatures by the temperature difference.
Note 7: Response time is measured with a 100mV step and 5mV
overdrive. The output load is a 500Ω resistor tied to 5V. Time
measurement is taken when the output crosses 1.4V.
Note 8: Do not short the STROBE pin to ground. It should be current
driven at 3mA to 5mA for the shortest strobe time. Currents as low
as 500µA will strobe the LT1011A if speed is not important. External
leakage on the STROBE pin in excess of 0.2µA when the strobe is “off”
can cause offset voltage shifts.
Note 9: See graph “Input Offset Voltage vs Common Mode Voltage.”