SIT9003AC-33-33SD-72.00000X

Rev. 1.7 Page 7 of 9 www.sitime.com
The Smart Timing Choice
The Smart Timing Choice
SiT9003
Low Power Spread Spectrum Oscillator
Notes:
8. Top marking: Y denotes manufacturing origin and XXXX denotes manufacturing lot number. The value of “Y” will depend on the assembly location of the device.
9. A capacitor of value 0.1 µF between Vdd and GND is required.
Dimensions and Patterns
Package Size – Dimensions (Unit: mm)
[8]
Recommended Land Pattern (Unit: mm)
[9]
7.0 x 5.0 x 0.90 mm (with Center-Pad)
0.90±0.10
Do not Connect the center pad
or
Connect it to Device’s GND
YXXXX
5.08
3.81
2.2
2.0
Rev. 1.7 Page 8 of 9 www.sitime.com
The Smart Timing Choice
The Smart Timing Choice
SiT9003
Low Power Spread Spectrum Oscillator
Ordering Information
The Part No. Guide is for reference only. To customize and build an exact part number, use the SiTime Part Number
Generator.
Available Spread Options vs. Temperature and Frequency
Spread Percentage
Temperature Range
C = -20 to 70°C I = -40 to 85°C
B = ±0.25% 1-110 MHz
D = ±0.50% 1-75 MHz
O = -0.50% 1-110 MHz
Q = -1.0% 1-75 MHz
Ordering Codes for Supported Tape & Reel Packing Method
Device Size 12 mm T&R (3ku) 12 mm T&R (1ku) 16 mm T&R (3ku) 16 mm T&R (1ku)
2.5 x 2.0 mm T Y
3.2 x 2.5 mm T Y
5.0 x 3.2 mm T Y
7.0 x 5.0 mm T Y
Frequency
1.00000 to 110.00000 MHz
Part Family
“SiT9003
Revision Letter
“A” is the revision
Temperature Range
“I” Industrial, -40 to 85ºC
Supply Voltage
Packaging
Leave Blank for Bulk
Feature Pin
“E” for Output Enable
“S” for Standby
“C” Commercial, -20 to 70ºC
Package Size
“1” 2.5 x 2.0 mm
“2” 3.2 x 2.5 mm
“3” 5.0 x 3.2 mm
“T” and “Y” ordering codes for
appropriate T&R. Please refer to
the table below.
“4” 7.0 x 5.0 mm
(With Center Pad)
SiT9003AC -14-18EB-66. 6 6600 T
Output Drive Strength
“–” Default (datasheet limits)
See “Drive Strength Settings”
“U”
“X”
“Z”
“H”
Spread Spectrum Percentage
“B” for ±0.25%
Frequency Stability
“3” for ±50 PPM
“4” for ±100 PPM
“D” for Spread Disable
“D” for ±0.50%
“O” for -0.50%
“Q” for -1.0%
“8” 7.0 x 5.0 mm
(Without Center Pad)
“18” for 1.8V
“25” for 2.5V
“28” for 2.8V
“33” for 3.3V
Rev. 1.7 Page 9 of 9 www.sitime.com
© SiTime Corporation 2013. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage or defect of a
Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii)
unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or (iv) improper
installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress.
Disclaimer: SiTime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and all express or implied warranties, either in fact or by
operation of law, statutory or otherwise, including the implied warranties of merchantability and fitness for use or a particular purpose, and any implied warranty arising from course of dealing or
usage of trade, as well as any common-law duties relating to accuracy or lack of negligence, with respect to this material, any SiTime product and any product documentation. Products sold by
SiTime are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved
or at stake. All sales are made conditioned upon compliance with the critical uses policy set forth below.
CRITICAL USE EXCLUSION POLICY
BUYER AGREES NOT TO USE SITIME'S PRODUCTS FOR ANY APPLICATION OR IN ANY COMPONENTS USED IN LIFE SUPPORT DEVICES OR TO OPERATE NUCLEAR FACILITIES
OR FOR USE IN OTHER MISSION-CRITICAL APPLICATIONS OR COMPONENTS WHERE HUMAN LIFE OR PROPERTY MAY BE AT STAKE.
SiTime owns all rights, title and interest to the intellectual property related to SiTime's products, including any software, firmware, copyright, patent, or trademark. The sale of SiTime products
does not convey or imply any license under patent or other rights. SiTime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the
sale of products or services by SiTime. Unless otherwise agreed to in writing by SiTime, any reproduction, modification, translation, compilation, or representation of this material shall be strictly
prohibited.
The Smart Timing Choice
The Smart Timing Choice
Low Power Spread Spectrum Oscillator
SiT9003
Revision History
Version Release Date Change Summary
1.62 8/20/13 Added drive strength settings
1.7 11/18/13 Revised rise and fall time tables, added 7050 package diagram with center pad, add thermal considerations.

SIT9003AC-33-33SD-72.00000X

Mfr. #:
Manufacturer:
Description:
MEMS OSC XO 72.0000MHZ LVCMOS LV
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union