PhotoIC Coupler 50 Mbps type (APS1)
–7–
ASCTB367E 201609-T
13. Coupler packaging format
1) Tape and reel (Unit: mm inch)
Tape dimensions Dimensions of tape reel
(1) When picked from 1/2-pin side: Part No. APS1551SX (Shown above)
(2) When picked from 3/4/5-pin side: Part No. APS1551SZ
10. Cleaning solvents compatibility
Cleaning the solder flux should use the immersion washing with
an cleaning solvent (Asahiklin AK-225). If you have to use
ultrasonic cleaning, please adopt the following conditions and
check that there are no problems in the actual usage.
• Frequency: 27 to 29 kHz
• Ultrasonic output: No greater than 0.25 W/cm
2
*
• Cleaning time: 30 s or less
• Others: Float PCB and the device in cleaning solvent to prevent
from contacting the ultrasonic vibrator.
*Note: Applies to unit area of ultrasonic output for ultrasonic baths.
11. Transportation and storage
(1) Extreme vibration during transport may deform the lead or
damage the coupler. Please handle the outer and inner boxes
with care.
(2) Inadequate storage condition may degrade soldering,
appearance and characteristics.
The following storage conditions are recommended:
• Temperature: 0 to 45 °C 32 to 113 °F
• Humidity: Max. 70 %RH
• Atmosphere: No harmful gasses such as sulfurous acid gas
and not dusty.
(3) In case the heat stress of soldering is applied to the coupler
which absorb moisture inside of its package, the evaporation of
the moisture increases the pressure inside the package and it
may cause the package blister or crack. This coupler is sensitive
to moisture and it is packed in the sealed moisture-proof
package. Please make sure the following condition after
unsealing.
*Please use the coupler immediately after unsealing. (within 30
days at 0 to 30 °C 32 to 86 °F and Max. 70%RH)
*If the coupler will be kept for a long time after unsealing, please
pack in the another moisture-proof package containing silica gel
and store. (Please use within 90days)
12. Water condensation
Water condensation occurs when the ambient temperature
changes suddenly from a high temperature to low temperature
at high humidity, or the coupler is suddenly transferred from a
low ambient temperature to a high temperature and humidity.
Condensation causes the failures such as insulation
deterioration. Panasonic Corporation does not guarantee the
failures caused by water condensation.
The heat conduction by the equipment the coupler is mounted
may accelerate inside equipment water condensation. Please
confirm no that there are condensation in the worst condition of
the actual usage.
(Special attention should be paid when high temperature heating
parts are close to the coupler.)
2.8
±0.3
7.2
±0.1
2
±0.1
4.7
±0.1
0.3
±0.05
12
±0.1
4
±0.1
.110
±.012
.283
±.004
.012
±.002
.157
±.004
5.5
±0.1
1.75
±0.1
.185
±.004
.217
±.004
.069
±.004
12
±0.3
.472
±.012
1.55
±0.1
dia.
.079
±.004
.472
±.004
.061
±.004
dia.
Tractor feed holes
1.55
±0.05
dia.
.061
±.002
dia.
Direction of picking
Device mounted
on tape
254
±2
dia.
13.4
±2
2
±0.5
21
±0.8
80
±1
dia.
10.000
±.079
dia.
3.150
±.039
dia.
2
±0.5
13
±0.5
dia.
.528
±.079
.079
±.020
.827
±.031
.079
±.020
.512
±.020
dia.
