OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

96R1A-R22-A13L

P1-P3P4-P4
Features
■ Virtually infi nite electrical circuit isolation
■ Sealed for board wash
■ Metal or plastic shaft options
■ RoHS compliant*
Model 96 - 5/8 ” Square Sealed Single-Turn Panel Control
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifi cations are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specifi c applications.
Initial Electrical Characteristics
1
Conductive Plastic Element Cermet Element
Standard Resistance Range
Linear Tapers (A, B, E, & H) .........................(B & E) 1 K ohms to 1 megohm ......................... (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) .................(D,G,S, & T) 1 K ohms to 1 megohm ................. (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance ...............................10 % or 20 % .................................................... 5% or 10%
Independent Linearity .......................................±5 % .................................................................. ±5 %
Absolute Minimum Resistance .........................2 ohms maximum .............................................. 2 ohms maximum
Effective Electrical Angle ..................................(Linear tapers) 240 ° ± 5 ° .................................. (Linear tapers) 240 ° ± 6 °
(Audio tapers) 225 ° ± 5 ° .................................. (Audio tapers) 225 ° ± 6 °
Contact Resistance Variation ...........................±1 % .................................................................. ±1 % or 3 ohms (whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Sea Level ....................................................1,500 VAC minimum .......................................... 1,500 VAC minimum
70,000 Feet .................................................500 VAC minimum ............................................. 500 VAC minimum
Insulation Resistance (500 VDC) ......................1,000 megohms minimum ................................. 1,000 megohms minimum
Power Rating (Voltage Limited By Power Dissipation or 350 VAC, Whichever Is Less)
+70 °C Single Section Assembly ................(Linear tapers) 1 watt ......................................... (Linear tapers) 2 watts
(Audio tapers) 0.5 watt ...................................... (Audio tapers) 1 watt
+125 °C .......................................................0 watt ................................................................. 0 watt
Theoretical Resolution ......................................Essentially infi nite .............................................. Essentially infi nite
Environmental Characteristics
1
Operating Temperature Range .......................... -40 °C to +125 °C ................................................ -40 °C to +125 °C
Storage Temperature Range .............................. -55 °C to +125 °C ................................................-55 °C to +125 °C
Temperature Coeffi cient Over Storage
Temperature Range .......................................... ±1,000 ppm/°C .....................................................±150 ppm/°C
Vibration (Single Section) ................................... 15 G ...................................................................... 15 G
Total Resistance Shift ................................... ±2 % maximum ....................................................±2 % maximum
Voltage Ratio Shift ........................................ ±5 % maximum .................................................... ±5 % maximum
Shock (Single Section) ....................................... 30 G ......................................................................30 G
Total Resistance Shift ................................... ±2 % maximum ....................................................±2 % maximum
Voltage Ratio Shift ........................................ ±5 % maximum .................................................... ±5 % maximum
Load Life ............................................................ 1,000 hours .......................................................... 1,000 hours
Total Resistance Shift ................................... ±10 % maximum ..................................................±5 % maximum
Rotational Life (No Load) ................................... 100,000 cycles ..................................................... 100,000 cycles
Total Resistance Shift ................................... (Linear tapers) 10 ohms or ±15 % TRS max. ...... (All tapers) ±5 % TRS max.
(whichever is greater)
(Audio tapers) ±20 % maximum
Contact Resistance Variation
@ 50,000 cycles ........................................... (Linear tapers) ±2 % ............................................. ±2 %
(Audio tapers) ±3 % ............................................. ±3 %
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift ................................... (Linear tapers) ±10 % TRS maximum .................(All tapers) ±5 % TRS maximum
(Audio tapers) ±20 % TRS maximum
Insulation Resistance (500 VDC) .................. 100 megohms minimum ......................................100 megohms minimum
IP Rating ............................................................. IP 65 .....................................................................IP 65
*RoHS COMPLIANT
Model 96 PC Pin Terminals, In-Line
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
1
3
CCW
2
POTENTIOMETER
Shaft Flat Orientation
DIA.
13.72 ± 0.38
(.540 ± .015)
15.88
(.625)
12.95 ± .203
(.510 ± .008)
MOUNTING
SURFACE
L
0.76 ± 0.05
(.030 ± .002)
TYP.
BACK VIEW
2.54
(.100)
2.54
(.100)
0.79 ± .025
(.031 ± .010)
1.19
(.047)
“A” STYLE
A.R. LUG
R
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
7.92
(.312)
9.53
(.375)
15.29 ± 0.56
(.602 ± .022)
SEE HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
3
2
1
R1
11.05 ± 0.20
(.435 ± .008)
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
(.015 )
FRACTION ± 1/64
.XX ±
(.38)
ANGLE ±5 °
.381
9.65
Specifi cations are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specifi c applications.
Mechanical Characteristics
1
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Mechanical Angle .................................................................................................................................................................................300 ° ±5 °
Torque
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A & R Bushings) .................................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Metal Bushing) ...............................................................................................................................12.7 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. Immersion wash is not recommended.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE: Performance specifi cations do not apply to units subjected to printed circuit board immersion cleaning processes.
1
At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Product Dimensions
Model 96 - 5/8 ” Square Sealed Single-Turn Panel Control
DIMENSIONS:
MM
(INCHES)
Specifi cations are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specifi c applications.
Model 96 - 5/8 ” Square Sealed Single-Turn Panel Control
Product Dimensions
Plastic
Shaft
Styles
1.60+.38/-.00
(.063+.015/-.000)
11.18 ± .38
(.440 ± .015)
1.60+.38/-.00
(.063+.015/-.000)
1.80 ± 0.25
(.071 ± .010)
1.50 ± 0.25
(.059 ± .010)
“F” ± .38
(“F” ± .015)
6.32+.000/-.152
(.249+.000/.006)
DIA.
6.30+.000/-.152
(.248+.000/.006)
DIA.
5.49
(.216)
6.32+.010/-.025
(.2490+.0004/.0010)
DIA.
1.194
(.047)
5.486 ± .051
(.216 ± .002)
1.19
(.047)
6.31+.025/-.051
(.2485+.001/.002)
DIA.
14.27 ± .25
(.562 ± .010)
1.80 ± .25
(0.07 ± .001)
1.00
(.04)
1.50 ± .25
(0.06 ± .001)
3.16+.00/-.15
(.1245+.000/-.006)
DIA.
48 TOOTH
5.994 +0.000/-0.051
(.236 +.000/-.002)
DIA.
DIA.
3.988 +0.000/-0.051
(.157 +.000/-.002)
SHAFT TYPE "B" (USES BUSHING A) SHAFT TYPE "D" (USES BUSHING C)
SHAFT TYPE "T" (USES BUSHING U)
SHAFT TYPE "C" (USES BUSHING A) SHAFT TYPE "R" (USES BUSHING R) SHAFT TYPE "W" (USES BUSHING A)
SHAFT TYPE "A" (USES BUSHING A)
SHAFT TYPE "H" (USES BUSHING A)
SHAFT TYPE "V" (USES BUSHING U)
SHAFT TYPE "G" (USES BUSHING A)
SHAFT TYPE "J" (USES BUSHING R)
TOLERANCES EXCEPT AS SHOWN: .XX = ±
.79
(0.03)
STD. LENGTHS:
25.40
(1.00)
.02
(.050)
.XXX = ±
.005
(.127)
.XXXX = ±
.0005
(.0127)
6.32+.010/-.025
(.2490+.0004/.0010)
DIA
6.32+.010/-.025
(.2490+.0004/.0010)
DIA
1.00 ± 0.13
(.039 ± .054)
6.00+.000/-.035
(.2362+.0000/.0010)
DIA
12.70
(.500)
15.88
(.625)
19.05
(.750)
22.23
(.875)
25.4
(1.000)
16.0
(.630)
22.0
(.866)
Metal
Shaft
Styles
0.79 ± 0.13
(.031 ± .054)
3.99+.000/-.035
(.1571+.0000/.0010)
DIA
STD. LENGTHS:
STD. LENGTHS:
STD. LENGTHS:
12.70
(.500)
15.88
(.625)
19.05
(.750)
22.23
(.875)
STD. LENGTHS:
19.05
(.750)
22.23
(.875)
12.70
(.500)
15.88
(.625)
19.05
(.750)
STD. LENGTHS:
12.70
(.500)
15.88
(.625)
19.05
(.750)
22.23
(.875)
STD. LENGTHS:
16.0
(.630)
22.0
(.866)
STD. LENGTHS:
16.0
(.630)
22.0
(.866)
STD. LENGTHS:
STD. LENGTHS:
19.05
(.750)
22.23
(.875)
“F” ± .381
(“F” ± .015)
3.988 ± .076
(.157 ± .003)
SHAFT TYPE "S" (USES BUSHING R)
6.000+.000/-.035
(.2362+.0000/.0014)
DIA
0.79 ± 0.25
(.031 ± .010)
SHAFT TYPE "E" (USES BUSHING C)
0.79
(.031)
3.16
(.1245)
DIA
12.0
(.500)
16.0
(.625)
19.0
(.750)
STD. LENGTHS:
STD. LENGTHS:
16.0
(.630)
22.0
(.866)
STD. LENGTHS:
16.0
(.630)
22.0
(.866)
7.95
(.313)
11.13
(.438)
FLAT LENGTH “F”:
6.99
(.275)
12.98
(.511)
FLAT LENGTH “F”:
DIMENSIONS:
MM
(INCHES)
P1-P3P4-P4

96R1A-R22-A13L

Mfr. #:
Buy 96R1A-R22-A13L
Manufacturer:
Bourns
Description:
Potentiometers 5K 10% 5/8" SQ ST
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet