AON6236
Symbol Min Typ Max Units
BV
DSS
40 V
V
DS
=40V, V
GS
=0V 1
T
J
=55°C 5
I
GSS
±100 nA
V
GS(th)
Gate Threshold Voltage
1.4 1.85 2.4 V
I
D(ON)
120 A
5.6 7
T
J
=125°C 8.4 10.5
8 10.5 mΩ
g
FS
80 S
V
SD
0.72 1 V
I
S
30 A
C
iss
1225 pF
C
oss
318 pF
C
rss
26.5 pF
R
g
1.7 3.0 Ω
Q
g
(10V) 18.5 26 nC
Q
g
(4.5V) 8.2 12 nC
Q
gs
3.5 nC
Q
gd
2.5 nC
t
D(on)
6 ns
On state drain current
I
D
=250µA, V
GS
=0V
V
GS
=10V, V
DS
=5V
V
GS
=10V, I
D
=20A
Gate-Body leakage current
V
DS
=V
GS,
I
D
=250µA
V
DS
=0V, V
GS
=±20V
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Forward Transconductance
mΩ
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
V
GS
=0V, V
DS
=0V, f=1MHz
I
S
=1A,V
GS
=0V
V
DS
=5V, I
D
=20A
I
DSS
µA
Zero Gate Voltage Drain Current
Drain-Source Breakdown Voltage
V
GS
=4.5V, I
D
=20A
R
DS(ON)
Static Drain-Source On-Resistance
Diode Forward Voltage
Reverse Transfer Capacitance
DYNAMIC PARAMETERS
Total Gate Charge
Gate Source Charge
Gate Drain Charge
Total Gate Charge
V
GS
=0V, V
DS
=20V, f=1MHz
Gate resistance
SWITCHING PARAMETERS
Turn-On DelayTime
V
GS
=10V, V
DS
=20V, I
D
=20A
r
t
D(off)
23.5 ns
t
f
3 ns
t
rr
14 ns
Q
rr
32.5
nC
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
I
F
=20A, dI/dt=500A/µs
Body Diode Reverse Recovery Charge
Body Diode Reverse Recovery Time
I
F
=20A, dI/dt=500A/µs
Turn-Off Fall Time
Turn-Off DelayTime
GS
DS
L
R
GEN
=3Ω
A. The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The
Power dissipation P
DSM
is based on R
θJA
and the maximum allowed junction temperature of 150°C. The value in any given application depends
on the user's specific board design.
B. The power dissipation P
D
is based on T
J(MAX)
=150°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=150°C. Ratings are based on low frequency and duty cycles to keep
initial T
J
=25°C.
D. The R
θJA
is the sum of the thermal impedance from junction to case R
θJC
and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedance which is measured with the device mounted to a large heatsink, assuming
a maximum junction temperature of T
J(MAX)
=150°C. The SOA curve provides a single pulse rating.
G. The maximum current rating is package limited.
H. These tests are performed with the device mounted on 1 in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C.
Rev 0: Oct. 2011 www.aosmd.com Page 2 of 6
