TDS LOCTITE GC 10, July-2015
DIRECTIONS FOR USE
Printing:
● LOCTITE GC 10 is available for stencil printing with Type 3 and
Type 4 powder.
● Printing at speeds between 25 to 125 mms
-1
can be achieved
using laser cut, electropolished or electroformed stencils with
metal squeegees.
Reflow:
● Suitable for convection, IR, hot belt and vapor phase.
● Proven profiles for multiple circuit board configurations.
Reflow Profile
Cleaning:
● Cleaning Solder Paste from Stencils:
● LOCTITE GC 10 is a no-clean solder paste designed to be
left on the PCB in many applications post assembly; it does
not pose a hazard to long-term reliability
● For stencil cleaning and cleaning board misprints, LOCTITE
MSC 01 solvent cleaner is recommended
.
● Cleaning Solder Paste from Circuit Boards:
● Residues can be removed using conventional cleaning
processes based on solvents, such as LOCTITE MCF 800.
● Cleaning of some assemblies is best conducted in an
ultrasonic bath.
● Tap water is not recommended for rinsing. Ionic impurities
present in tap water can lead to reduced reliability of the
assembly.
.
RELIABILITY PROPERTIES
Solder Paste Medium:
LOCTITE GC 10 medium contains a stable resin system, slow
evaporating solvents and with minimal odor. The formulation has been
tested to the requirements of the ANSI/J-STD-004B for a type ROL0
classification specifications.
Test Specification Results
Flux Corrosion J-STD004B (2.6.15C) Pass
Copper Mirror J-STD004B (2.3.32D) Pass
Surface Insulation
Resistance (SIR)
J-STD004B (2.6.3.7) Pass
Electromigration (ECM) J-STD004B (2.6.14.1) Pass
Flux Activity Classification J-STD004B ROL0
PACKAGING
LOCTITE GC 10 is available in both jars and semco cartridges. Other
types of packaging may be available on request.
Storage:
Optimal storage: 5 to 25ºC (± 1.5°C)
Storage information may be indicated on the product container
labelling. Material removed from containers may be contaminated
during use. Do not return products to the original container. Henkel
Corporation cannot assume responsibility for product that has been
contaminated or stored under conditions other than those previously
indicated. If additional information is required, please contact your
local Technical Service Center or Customer Service Representative.
Shelf Life:
Provided that LOCTITE GC 10 is stored in the original container, a
minimum shelf life of 365 days at 5 to 25˚C (± 1.5°C) or 31 days at
40°C can be expected.
DATA RANGES
The data contained herein may be reported as a typical value and/or a
range. Values are based on actual test data and are verified on a
periodic basis.
GENERAL INFORMATION
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Not for Product Specifications
The technical information contained herein is intended for reference
only. Please contact Henkel Technologies Technical Service for
assistance and recommendations on specifications for this product.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
Americas Europe Asia
+1.888.943.6535 +32.1457.5611 +86.21.3898.4800
For the most direct access to local sales and technical support visit:www.henkel.com/electronics
