2902823 Datasheet 2902823 | P4-P6

MINI MCR-SL-CVS-24-5-10-NC

105264_en_01 PHOENIX CONTACT 4

4 Technical data

Input

Voltage input signal 9.6 V DC ... 30 V DC

Output

Max. voltage output signal 10 V DC

7.5 V DC

5 V DC

2.5 V DC

Configurable/programmable Yes, preconfigured

Short-circuit current approx. 32 mA

Ripple < 20 mV

Supply

Nominal supply voltage 24 V DC

Supply voltage range 9.6 V DC ... 30 V DC (The T connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order

No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a

35 mm DIN rail according to EN60715))

Max. current consumption < 25 mA (10V output with 30mA load at 24V DC IN)

< 65 mA (10V output with 30mA load at 9.6V DC IN)

< 50 mA (10V voltage output with 30 mA load at 12V DC IN)

< 20 mA (10V voltage output with 30 mA load at 30V DC IN)

Power consumption < 600 mW (at 24 V IN)

< 624 mW (at 9.6 V IN)

< 564 mW (At 12 V IN)

< 540 mW (At 30 V IN)

General data

Maximum transmission error ≤ 0.1 % (of final value)

≤ 0.5 % (Without adjustment)

Temperature coefficient, typical < 0.002 %/K

Maximum temperature coefficient < 0.01 %/K

Electrical isolation Basic insulation according to EN 61010

Surge voltage category II

Mounting position Any

Degree of protection IP20

Pollution degree 2

Rated insulation voltage 50 V AC/DC

Dimensions W / H / D 6.2 mm / 93.1 mm / 102.5 mm

Type of housing PBT green

Connection data Screw connection Spring-cage conn.

Conductor cross section, solid 0.2 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm²

Conductor cross section, stranded 0.2 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm²

Stripping length 12 mm 8 mm

Ambient conditions

Ambient temperature (operation) -20 °C ... 65 °C

Ambient temperature (storage/transport) -40 °C ... 85 °C

MINI MCR-SL-CVS-24-5-10-NC

105264_en_01 PHOENIX CONTACT 5

Conformance with EMC Directive 2004/108/EC

Noise immunity according to EN 61000-6-2

When being exposed to interference, there may be minimal deviations.

Noise emission according to EN 61000-6-4

Conformance / approvals

Conformance CE-compliant

ATEX  II 3 G Ex nA IIC T4 Gc X

UL, USA / Canada 508 listed

UL, USA / Canada Class I, Div. 2, Groups A, B, C, D T5 applied for

MINI MCR-SL-CVS-24-5-10-NC

105264_en_01 PHOENIX CONTACT 6

5 Safety regulations and installation notes

5.1 Installation notes

– The category 3 device is suitable for installation in the

zone 2 potentially explosive area. It fulfills the require-

ments of EN60079-0:2009 and EN60079-15:2010.

– Installation, operation, and maintenance may only be

carried out by qualified electricians. Follow the installa-

tion instructions described. When installing and operat-

ing the device, the applicable regulations and safety

directives (including national safety directives), as well

as general technical regulations, must be observed.

The technical data is provided in this package slip and

on the certificates (conformity assessment, additional

approvals where applicable).

– It is not permissible to open or modify the device. Do not

repair the device yourself but replace it with an equiva-

lent device. Repairs may only be carried out by the man-

ufacturer. The manufacturer is not liable for damage

resulting from violation.

– The IP20 degree of protection (IEC60529/EN60529) of

the device is intended for use in a clean and dry environ-

ment. Do not subject the device to any load that ex-

ceeds the described limits.

– The device is not designed for use in atmospheres with

a danger of dust explosions.

5.2 Installation in the Ex area (zone 2)

– Observe the specified conditions for use in potentially

explosive areas.

– The device must be installed in a housing (control or dis-

tributor box) which meets the requirements of EN

60079-15 and provides at least IP54 (EN 60529) degree

of protection.

– During installation and when connecting the supply and

signal circuits, observe the requirements of EN 60079-

14. Devices may only be connected to circuits in zone 2

if they are suitable for operation in Ex zone 2 and for the

prevailing conditions at the place of use.

– In potentially explosive areas, terminals may only be

snapped onto or off the DIN rail connector and wires

may only be connected or disconnected when the pow-

er is switched off.

– The device must be stopped and immediately removed

from the Ex area if it is damaged, has been subjected to

an impermissible load, has been stored incorrectly, or if

it malfunctions.

– You can download the latest documents for these de-

vices from www.phoenixcontact.net/products.

P1-P3 P4-P6 P7-P9

2902823

Mfr. #:

Buy 2902823

Manufacturer:

Phoenix Contact

Description:

Terminal Block Interface Modules MINI MCR-SL-CVS 24-5-10-SP-NC

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

2902823