ELECTRICAL CHARACTERISTICS @25°C
MCC
PART
NUMBER
ZENER
VOLTAGE
V
Z
TEST
CURRENT
I
ZT
MAXIMUM
DYNAMIC
IMPEDANCE
Z
ZT
@ I
ZT
MAXIMUM
REVERSE
CURRENT
I
R
@ V
R
TEST
VOLTAGE
V
R
MAXIMUM
REGULATOR
CURRENT
IZM
TA = 50°C
MAXIMUM
KNEE
IMPEDANCE
Z
ZK
@ I
ZK
TEST
CURRENT
I
ZK
MAXIMUM
SURGE
CURRENT
I
S
VOLTS mA OHMS µA VOLTS mA OHMS mA mA
DL4728 3.3 76 10 100 1 276 400 1.0 1280
DL4729 3.6 69 10 100 1 252 400 1.0 1260
DL4730 3.9 64 9 50 1 234 400 1.0 1190
DL4731 4.3 58 9 10 1 217 400 1.0 1070
DL4732 4.7 53 8 10 1 193 500 1.0 970
DL4733 5.1 49 7 10 1 178 550 1.0 890
DL4734 5.6 45 5 10 2 162 600 1.0 810
DL4735 6.2 41 2 10 3 146 700 1.0 730
DL4736 6.8 37 3.5 10 4 133 700 1.0 660
DL4737 7.5 34 4.0 10 5 121 700 0.5 605
DL4738 8.2 31 4.5 10 6 110 700 0.5 550
DL4739 9.1 28 5.0 10 7 100 700 0.5 500
DL4740 10 25 7 10 7.6 91 700 0.25 454
DL4741 11 23 8 5 8.4 83 700 0.25 414
DL4742 12 21 9 5 9.1 76 700 0.25 380
DL4743 13 19 10 5 9.9 69 700 0.25 344
DL4744 15 17 14 5 11.4 61 700 0.25 304
DL4745 16 15.5 16 5 12.2 57 700 0.25 285
DL4746 18 14 20 5 13.7 50 750 0.25 250
DL4747 20 12.5 22 5 15.2 45 750 0.25 225
DL4748 22 11.5 23 5 16.7 41 750 0.25 205
DL4749 24 10.5 25 5 18.2 38 750 0.25 190
DL4750 27 9.5 35 5 20.6 34 750 0.25 170
DL4751 30 8.5 40 5 22.8 30 1000 0.25 150
DL4752 33 7.5 45 5 25.1 27 1000 0.25 135
DL4753 36 7.0 50 5 27.4 25 1000 0.25 125
DL4754 39 6.5 60 5 29.7 23 1000 0.25 115
DL4755 43 6.0 70 5 32.7 22 1500 0.25 110
DL4756 47 5.5 80 5 35.8 19 1500 0.25 95
DL4757 51 5.0 95 5 38.8 18 1500 0.25 90
DL4758 56 4.5 110 5 42.6 16 2000 0.25 80
DL4759 62 4.0 125 5 47.1 14 2000 0.25 70
DL4760 68 3.7 150 5 51.7 13 2000 0.25 65
DL4761 75 3.3 175 5 56.0 12 2000 0.25 60
NOTE 1 The JEDEC type numbers shown have A 5% tolerance on nominal zener voltage.
No
suffix
signifies
10% tolerance, A signifies 5% tolerance, C signifies 2% tolerance.
NOTE 2 The zener impedance is derived from the 60Hz AC voltage, which results when an AC current having an rms value equal to
10% of the DC zener current (Izt or Izk) is superimposed on Izt or Izk. Zener impedance is measured at two points to insure
a sharp knee on the breakdown curve and eliminate unstable units.
NOTE 3 The reverse surge current is measured at 25
o
C ambient using a 1/2 square wave or equivalent sine wave pulse 1/120 second
duration superimposed on Izt
NOTE 4 Voltage measurements to be performed 90 seconds after application of DC current.
DL4728 thru DL4761
Revision: B 2011/09/06
TM
Micro Commercial Components
2 of 3
