DM200-01-1-9080-0-LC

DM200-01-0/1/2 CML
TM
Butterfly Transmitter Product Specification – May 2007
F i n i s a r
Finisar Corporation –10-May-07 Rev_A Page 4
IV. Standard Operating Specifications
Table 2: Standard Operating Requirements
Item
Parameters Min Typ Max Units Comments
1.
Bit Rate 9.953/10.7 11.1 Gb/s
All the following
transmission
parameters are
tested at 9.95 or
10.7Gb/s
2.
Operating Case
Temperature Range
-5 75 °C
3.
Wavelength (SOL)
ITU-T
Wavelength
ITU-T wavelengths
defined in Tables 9
& 10
4.
Locked deviation from
ITU
-2.5 2.5 GHz EOLOT
5.
Modulated Output Power
(EOL)
0 3 dBm
SOL operation
condition to be
discussed.
6.
Operating Drive current
(SOL)
70 100 mA
7.
Allowed Deviation from
SOL drive current over
life and temperature
-15 20 %
8.
Required Resolution of
Operating Drive Current
0.09 mA 360mA/4096 levels
9.
SMSR 35 40 dB
10.
Wavelength temperature
tuning coefficient
0.1 nm/°C
11.
Wavelength current
tuning coefficient
7
pm/m
A
12.
Laser threshold current 25 mA
13.
Forward Bias Voltage 1.8 V
14.
RIN -135 dB/Hz
0 to 10 GHz,
Measured before
OSR is installed
15.
Laser CW Linewidth
(FWHM)
2 10 MHz
Measured before
OSR
16.
Module Input Impedance 50 Ohms
Recommend use of
EML driver
technology
17.
Peak to Peak voltage,
Vpp
0.5 1 1.5 V Into 50ohm
18.
Electrical input crossing 25 80 %
Customer must
provide adjustment
capability on
electrical driver
19.
Extinction Ratio
(EOLOT)
9 dB BT Filter OFF
20.
Optical crossing tbc tbc % BT Filter OFF
21.
S11 Mask dB tbc
22.
S21 (3dB BW) 10 GHz Before OSR
DM200-01-0/1/2 CML
TM
Butterfly Transmitter Product Specification – May 2007
F i n i s a r
Finisar Corporation –10-May-07 Rev_A Page 5
23.
Power dispersion Penalty
@ 30dB OSNR, 9.95Gbs,
BER=10
-12
, 3400ps/nm
(EOLOT)
1
2 dB
Receiver threshold
optimized for
3400ps/nm, same
threshold used for
BB measurement
24.
OSNR dispersion Penalty
@ BER=10
-4
, 10.7Gbs,
3400ps/nm (EOLOT)
1
2 dB
Receiver threshold
optimized at BB and
3400ps/nm
Note:
1. Please call Finisar to discuss the receiver configuration, including types of PIN/APD,
and power level into APD, and the type of CDRs are used. With FEC and some
CDRs incorporating EDC functions, >3400ps/nm transmission is possible.
V. Mechanical Details
Figure 3: Package Outline Drawing
DM200-01-0/1/2 CML
TM
Butterfly Transmitter Product Specification – May 2007
F i n i s a r
Finisar Corporation –10-May-07 Rev_A Page 6
VI. Pin-out Details
Figure 4: Schematic Pin-out of Transmitter Package
Table 3: Pin-Out Description
Pin Description
1. TEC#1 (+)
2. TEC#1 (-)
3. Thermistor#1 (+)
4. Thermistor#1 (-)
5. Laser Diode Bias
6. PD1 (Anode)
7. PD1 (Cathode)
8. PD2 (Cathode)
9. PD2 (Anode)
10. TEC 2 (+)
11. TEC 2 (-)
12. Thermistor#2 (+)
13. Thermistor#2 (-)
OSR
1
2
3
4
5
6
7
8
9
10 11 12 13
TEC#1
TEC#2
DFB
PD1 PD2
R=45Ω
L
Thermistor
Thermistor

DM200-01-1-9080-0-LC

Mfr. #:
Manufacturer:
Finisar Corporation
Description:
Laser Diodes DWDM CML, 100GHz spacing (C-band or L-band), OC-192, STM64, 10G FC, G.709, 10.7 Gb/s, G.959.1 P1L1 and P1V1 transmitter, butterfly package, LC connector, 0 to +3dBm output power, -5/75 C
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union