OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

XR17V358IB-E8-EVB

P1-P3P4-P6P7-P9P10-P10
1
REV. 1.0.1 XR17V358/354 EVALUATION BOARD USER’S MANUAL
1.0 INTRODUCTION
This user’s manual is for the XR17V358/354 evaluation board revision 3.x. The XR17V358 and XR17V354 are
available in the same package and are pin compatible, therefore they share the same evaluation board. This
user’s manual gives an overview of the evaluation board and the jumper settings for testing various modes
using the evaluation board. The ordering information for the XR17V358/354 evaluation board is as following:
ORDERING INFORMATION
PART NUMBER DESCRIPTION
XR17V354IB-0A-EVB
Single device XR17V354 is installed on the board.
XR17V354IB-E4-EVB
Two devices are installed on the board. The master device is XR17V354. The slave device
on expansion interface is a XR17V354.
XR17V354IB-E8-EVB
Two devices are installed on the board. The master device is XR17V354. The slave device
on expansion interface is a XR17V358.
XR17V358IB-0A-EVB
Single device XR17V358 is installed on the board.
XR17V358IB-E4-EVB
Two devices are installed on the board. The master device is XR17V358. The slave device
on expansion interface is a XR17V354.
XR17V358IB-E8-EVB
Two devices are installed on the board. The master device is XR17V358. The slave device
on expansion interface is a XR17V358.
2.0 OVERVIEW
This evaluation board has a x1 PCIe connector and will work in any x1, x4 or x16 PCIe slot. Up to 16 UART
ports can be tested on this evaluation board when 2 XR17V358 are installed. The PCIe interface of the master
device is connected directly to the PCIe connector. The master device communicates with the slave device via
Exar’s proprietary expansion interface. The PCIe interface on the slave device is not used.
FIGURE 1. PCIE AND EXPANSION INTERFACE
XR17V358/354
Master
Device
CLK+
CLK-
RX+
RX-
TX+
TX-
XR17V358/354
Slave
Device
CLK+
CLK-
RX+
RX-
TX+
TX-
Expansion
Interface
2
XR17V358/354 EVALUATION BOARD USER’S MANUAL REV. 1.0.1
2.1 Evaluation Board Components for Master Device
The table below shows all of the components that are on the evaluation board for the master device.
TABLE 1: COMPONENTS OF THE XR17V358 EVALUATION BOARD FOR MASTER DEVICE
UNIT PART FUNCTION
U2 XR17V358IB176-F
XR17V354IB176-F
XR17V358 or XR17V354 PCIe UART master device.
U16 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 0.
U11 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 1.
U25 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 2.
U24 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 3.
U28 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 4.
U27 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 5.
U17 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 6.
U22 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 7.
U6 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART RI# signals
channels 0-3.
U13 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART RI# signals
channels 4-7.
U9 SP3497EEN-L Exar RS-485 Transceiver for master device UART channel 4. Not
installed.
U10 SP3497EEN-L Exar RS-485 Transceiver for master device UART channel 5. Not
installed.
U21 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 3
and 4 for RS-485 full-duplex testing. Not installed.
U3 HSDL2300 IR Transceiver. Not installed.
U26 93C46 (PDIP) External EEPROM for storing Vendor ID and Device ID. Not installed.
U30 93C46 (TSSOP) External EEPROM for storing Vendor ID and Device ID. Installed, not
programmed.
2.2 Evaluation Board Components for Slave Device
The table below shows all of the components that are on the evaluation board for the slave device. If the slave
device is not installed, then these components will also not be installed.
TABLE 2: COMPONENTS OF THE XR17V358 EVALUATION BOARD FOR SLAVE DEVICE
UNIT PART FUNCTION
U1 XR17V358IB176-F
XR17V354IB176-F
XR17V358 or XR17V354 PCIe UART slave device.
U5 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 0.
U4 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 1.
U8 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 2.
3
REV. 1.0.1 XR17V358/354 EVALUATION BOARD USER’S MANUAL
2.3 Jumper Settings for Power Sources for Master Device
The following table shows the jumper settings for selecting/enabling the power source for the Master Device.
TABLE 3: JUMPER SETTINGS FOR POWER SOURCES FOR MASTER DEVICE
JUMPER FUNCTIONS COMMENTS
J45 3.3V supply voltage for the 3.3V Core Not installed. Trace between 1&2.
J42 Enables/Disables Internal Buck Regulator Jumper is not in - Internal buck regulator is enabled
(default).
J66 3.3V supply voltage for the output stage of buck regulator Not installed. Trace between 1&2.
J63 3.3V supply voltage for analog blocks of buck regulator Not installed. Trace between 1&2.
J62 1.2V regulated voltage from internal buck Not installed. Trace between 1&2.
J67 1.2V supply voltage for 1.2V PHY Not installed. Trace between 1&2.
J56 1.2V supply voltage for 1.2V Core Not installed. Trace between 1&2.
2.4 Jumper Settings for Power Sources for Slave Device
The following table shows the jumper settings for selecting/enabling the power source for the Slave Device.
TABLE 4: JUMPER SETTINGS FOR POWER SOURCES FOR SLAVE DEVICE
JUMPER FUNCTIONS COMMENTS
J32 3.3V supply voltage for the 3.3V Core Not installed. Trace between 1&2.
J31 Enables/Disables Internal Buck Regulator Jumper is not in - Internal buck regulator is enabled
(default).
J68 3.3V supply voltage for the output stage of buck regulator Not installed. Trace between 1&2.
J65 3.3V supply voltage for analog blocks of buck regulator Not installed. Trace between 1&2.
J64 1.2V regulated voltage from internal buck Not installed. Trace between 1&2.
J70 1.2V supply voltage for 1.2V PHY Not installed. Trace between 1&2.
J34 1.2V supply voltage for 1.2V Core Not installed. Trace between 1&2.
U7 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 3.
U15 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 4.
U14 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 5.
U19 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 6.
U20 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 7.
U12 SP3497EEN-L Exar RS-485 Transceiver for slave device UART channel 4.
U18 SP3497EEN-L Exar RS-485 Transceiver for slave device UART channel 5.
U23 SP336EEY-L Exar RS-232/RS-485 Transceiver for slave device UART channel 3
and 4 for RS-485 full-duplex testing. Not installed.
TABLE 2: COMPONENTS OF THE XR17V358 EVALUATION BOARD FOR SLAVE DEVICE
UNIT PART FUNCTION
P1-P3P4-P6P7-P9P10-P10

XR17V358IB-E8-EVB

Mfr. #:
Buy XR17V358IB-E8-EVB
Manufacturer:
MaxLinear
Description:
Interface Development Tools Eval Board for XR17V358IB-E8
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet