NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
SHEET 1 OF 1
LDCFDLT_A
SCALE: 2:1
TITLE:
SIZE
DWG. NO.
REV
DO NOT SCALE DRAWING
ANGLES:
1
TOLERANCES:
.020 [0.50]-.200 [5.00]=
.008 [0.20]
.200 [5.00]-1.200 [30.00]=
.016 [0.40]
1.20 [30.0]-4.75 [120.0]=
.024 [0.60]
4.75 [120.0]-12.40 [315.0]=
.040 [1.0]
DRAWN:
ENGR:
DT:
DT:
MATERIAL:
FINISH:
PROJECTION:
:
THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS
DESIGNATED AGENTS.
159 ORT LANE
MERLIN, OR 97532
B
12-JUL-12
B.MURPHY
S.HOGAN
12-JUL-12
REVISIONS
REV
DESCRIPTION
DATE
APPV
B
Added new title block, heat shrink and instructions 12-JUL-12 SAH
CONMCX012 ASSEMBLY INSTRUCTIONS
1. Strip the cable to the recommended dimensions.
2. Slip heat shrink and crimp ring onto stripped cable.
2. Slide the cable into the body until the center conductor is centered in the fork.
3. Push the braided shield over the barrel.
4. Solder the center conductor into the center of the fork.
5. Slide the crimp ring over the shield and crimp with a 0.128” hex crimp tool
(or one labeled for use with RG-174 cable).
6. Trim off any excess shield wire sticking out from the ring.
7. Slip the heat shrink over the crimp ring until it is against the body and shrink.
8. Insert insulator into body.
9. Push the cover into the opening.
Descripon Material Finish
Body
Pin
Insulaon
Gold
N/A
Gold
PTFE
Crimp Ring GoldBrass
Boyd Chuck GoldBE CU
Insulator
Cover
Heat Shrink
N/A
Gold
Black
PTFE
Brass
Polyolefin
Brass
Brass
Ø0.102
(2.60)
0.197
(5.00)
0.394
(10.00)
Ø0.148
(3.75)
0.339
(8.60)
0.165
(4.20)
BOYD CHUCK
0.3x3.9x5mm GROOVE
SIDE VIEW
0.079
(2.00)
0.035
(0.90)
0.173
(4.40)
0.171
(4.35)
0.197
(5.00)
TOP VIEW
INSULATOR
0.035
(0.90)
Ø0.157
(4.00)
COVER
0.197
(5.00)
0.138
(3.50)
RECOMMENDED CABLE STRIPPING DIMENSIONS
0.031
(0.80)
RG-174 Cable
Ø0.154
(3.90)
0.276
(7.00)
CRIMP RING
Ø0.197
(5.00)
0.787
(20.00)
HEAT SHRINK
BRAIDED SHIELD
MCX MALE RIGHT ANGLE
CABLE END CRIMP FOR RG174 CABLE
CONMCX012
