MPXH6300A
Sensors
4 Freescale Semiconductor, Inc.
2 Mechanical and Electrical Specifications
2.1 Maximum ratings
2.2 Operating characteristics
Table 2. Maximum ratings
(1)
1.Exposure beyond the specified limits may cause permanent damage or degradation to the device.
Parametrics Symbol Value Units
Maximum pressure (P1 > P2)
P
max
1200 kPa
Storage temperature
T
stg
-40 to +125 °C
Operating temperature
T
A
-40 to +125 °C
Output source current @ full-scale output
(2)
2.Maximum output current is controlled by effective impedance from V
OUT
to GND or V
OUT
to V
S
in the application circuit.
I
o
+0.5mAdc
Output sink current @ minimum pressure offset
(2)
I
o
--0.5mAdc
Table 3. Operating characteristics (V
S
= 5.1 V
DC
, T
A
= 25 °C unless otherwise noted, P1 > P2.)
Characteristic Symbol Min Typ Max Unit
Pressure range
P
OP
20 — 304 kPa
Supply voltage
(1)
1.Device is ratiometric within this specified excitation range.
V
S
4.74 5.1 5.46 V
DC
Supply current
I
O
— 6.0 10 mAdc
Minimum pressure offset
(2)
(0 to 85 °C) @ V
S
= 5.1 Volts
2.Offset (V
OFF
) is defined as the output voltage at the minimum rated pressure.
V
OFF
0.241 0.306 0.371 V
DC
Full-scale output
(3)
(0 to 85 °C) @ V
S
= 5.1 Volts
3.Full-scale output (V
FSO
) is defined as the output voltage at the maximum or full-rated pressure.
V
FSO
4.847 4.912 4.977 V
DC
Full-scale span
(4)
(0 to 85 °C) @ V
S
= 5.1 Volts
4.Full-scale span (V
FSS
) is defined as the algebraic difference between the output voltage at full-rated pressure and the output voltage at the
minimum rated pressures
V
FSS
4.476 4.606 4.736 V
DC
Accuracy
(5)
(0 to 85 °C)
5.Accuracy is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of span at
25 °C due to all sources of error including the following:
Linearity: Output deviation from a straight line relationship with pressure over the specified pressure range.
Temperature hysteresis:Output deviation at any temperature within the operating temperature range, after the temperature is cycled to
and from the minimum or maximum operating temperature points, with zero differential pressure applied.
Pressure hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from minimum
or maximum rated pressure at 25 °C
TcSpan: Output deviation over the temperature range of 0 to 85 °C, relative to 25 °C.
TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85 °C, relative to 25 °C.
Variation from Nominal: The variation from nominal values, for offset or full-scale span, as a percent of V
FSS
, at 25 °C.
———±1.5 %V
FSS
Sensitivity
V/P — 16.2 — mV/kPa
Response time
(6)
6.Response time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a
specified step change in pressure.
t
R
—1.0—ms
Warm-up time
(7)
7.Warm-up time is defined as the time required for the product to meet the specified output voltage after the pressure has been stabilized.
——20—ms
Offset stability
(8)
8.Offset stability is the product's output deviation when subjected to 1000 cycles of pulsed pressure, temperature cycling with bias test.
——±0.25 — %V
FSS
