Vishay Siliconix
DG454, DG455, DG456
Document Number: 74473
S12-2498-Rev. F, 22-Oct-12
www.vishay.com
4
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
For technical questions, contact: analogswitchtechsupport@vishay.com
Notes:
a. V
IN
= input voltage to perform proper function.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Parameter Symbol
Test Conditions
Unless Specified
V+ = 5 V, V- = - 5 V
V
IN
= 2.4 V, 0.8 V
a
Temp.
b
Typ.
c
- 40 °C to 125 °C - 40 °C to 85 °C
Unit
Min.
d
Max.
d
Min.
d
Max.
d
Power Supplies
Power Supply Current I+
V
IN
= 0 or 5 V
Room
Full
14 100
100
100
100
µANegative Supply Current I-
Room
Full
- 0.001 - 0.5
- 5
- 0.5
- 5
Ground Current
I
GND
Room
Full
- 14 - 100
- 100
- 100
- 100
SPECIFICATIONS FOR DUAL SUPPLIES
SPECIFICATIONS FOR UNIPOLAR SUPPLIES
Parameter Symbol
Test Conditions
Unless Specified
V+ = 12 V, V- = 0 V
V
IN
= 2.4 V, 0.8 V
a
Temp.
b
Typ.
c
- 40 °C to 125 °C - 40 °C to 85 °C
Unit
Min.
d
Max.
d
Min.
d
Max.
d
Analog Switch
Analog Signal Range
e
V
ANALOG
Full 12 12 V
On-Resistance
R
ON
I
S
= - 10 mA, V
D
= 0 V to + 10 V
Room
Full
5.5 8.1
12.4
8.1
10.4
On-Resistance Match
R
ON
I
S
= - 10 mA, V
D
= + 10 V
Room
Full
0.14 0.5
1
0.5
0.5
On-Resistance Flatness
R
FLATNESS
I
S
= - 10 mA,
V
D
= 0 V, + 5 V, + 10 V
Room
Full
0.94 1.5
1.7
1.5
1.5
Dynamic Characteristics
Tur n - O n T i m e
t
ON
R
L
= 300 , C
L
= 35 pF
V
S
= 8 V, See Figure 2
Room
Full
132 162
238
162
210
ns
Turn-Off Time
t
OFF
Room
Full
61 91
117
91
105
Break-Before-Make
Time Delay
t
D
DG456 only, V
S
= 8 V
R
L
= 300 , C
L
= 35 pF
Room 70
Charge Injection
e
Q
V
g
= 0 V, R
g
= 0 , C
L
= 1 nF
Room 1 pC
Power Supplies
Power Supply Current I+
V+ = 13.5 V, V- = 0 V
V
IN
= 0 or 5 V
Room
Full
25 100
100
100
100
µANegative Supply Current I-
Room
Full
- 0.001 - 0.5
- 5
- 0.5
- 5
Ground Current
I
GND
Room
Full
- 25 - 100
- 100
- 100
- 100
