![](/2022/pdf/453/902/bga.jpg)
6.42
10
IDT70V9389/289L
High-Speed 3.3V 64K x18/x16 Dual-Port Synchronous Pipelined Static RAM Industrial & Commercial Temperature Ranges
AC Electrical Characteristics Over the Operating Temperature Range
(Read and Write Cycle Timing)
(3)
(VDD = 3.3V ± 0.3V)
NOTES:
1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). This parameter is guaranteed by device characteriza-
tion, but is not production tested.
2. The Pipelined output parameters (t
CYC2, tCD2) apply to either or both the Left and Right ports when FT/PIPE = VIH. Flow-through parameters (tCYC1, tCD1) apply
when FT/PIPE = V
IL for that port.
3. All input signals are synchronous with respect to the clock except for the asynchronous Output Enable (OE), FT/PIPE
R, and FT/PIPEL.
70V9389/289L7
Com'l Only
70V9389/289L9
Com'l & Ind
70V9389/289L12
Com'l Only
Symbol Parameter Min.Max.Min.Max.Min.Max.Unit
t
CYC1
Clock Cycle Time (Flow-Through)
(2)
22
____
25
____
30
____
ns
t
CYC2
Clock Cycle Time (Pipelined)
(2)
12
____
15
____
20
____
ns
t
CH1
Clock High Time (Flow-Through)
(2)
7.5
____
12
____
12
____
ns
t
CL1
Clock Low Time (Flow-Through)
(2)
7.5
____
12
____
12
____
ns
t
CH2
Clock High Time (Pipelined)
(2)
5
____
6
____
8
____
ns
t
CL2
Clock Low Time (Pipelined)
(2)
5
____
6
____
8
____
ns
t
R
Clock Rise Time
____
3
____
3
____
3ns
t
F
Clock Fall Time
____
3
____
3
____
3ns
t
SA
Address Setup Time 4
____
4
____
4
____
ns
t
HA
Address Hold Time 0
____
1
____
1
____
ns
t
SC
Chip Enable Setup Time 4
____
4
____
4
____
ns
t
HC
Chip Enable Hold Time 0
____
1
____
1
____
ns
t
SB
Byte Enable Setup Time 4
____
4
____
4
____
ns
t
HB
Byte Enable Hold Time 0
____
1
____
1
____
ns
t
SW
R/W Setup Time 4
____
4
____
4
____
ns
t
HW
R/W Hold Time 0
____
1
____
1
____
ns
t
SD
Input Data Setup Time 4
____
4
____
4
____
ns
t
HD
Input Data Hold Time 0
____
1
____
1
____
ns
t
SAD
ADS Setup Time
4
____
4
____
4
____
ns
t
HAD
ADS Hold Time
0
____
1
____
1
____
ns
t
SCN
CNTEN Setup Time
4
____
4
____
4
____
ns
t
HCN
CNTEN Hold Time
0
____
1
____
1
____
ns
t
SRST
CNTRST Setup Time
4
____
4
____
4
____
ns
t
HRST
CNTRST Hold Time
0
____
1
____
1
____
ns
t
OE
Output Enable to Data Valid
____
7.5
____
9
____
12 ns
t
OLZ
Output Enable to Output Low-Z
(1)
2
____
2
____
2
____
ns
t
OHZ
Output Enable to Output High-Z
(1)
17 17 17ns
t
CD1
Clock to Data Valid (Flow-Through)
(2)
____
18
____
20
____
25 ns
t
CD2
Clock to Data Valid (Pipelined)
(2)
____
7.5
____
9
____
12 ns
t
DC
Data Output Hold After Clock High 2
____
2
____
2
____
ns
t
CKHZ
Clock High to Output High-Z
(1)
292929ns
t
CKLZ
Clock High to Output Low-Z
(1)
2
____
2
____
2
____
ns
Port-to-Port Delay
t
CWDD
Write Port Clock High to Read Data Delay
____
28
____
35
____
40 ns
t
CCS
Clock-to-Clock Setup Time
____
10
____
15
____
15 ns
4856 tbl 11a