LT3973/LT3973-3.3/LT3973-5
18
3973fb
For more information www.linear.com/LT3973
Figure 9. A Good PCB Layout Ensures Proper, Low EMI Operation
a few µA in this state. If the EN/UVLO pin is grounded, the
SW pin current will drop to 0.75µA. However, if the V
IN
pin
is grounded while the output is held high, regardless of EN/
UVLO, parasitic diodes inside the LT3973 can pull current
from the output through the SW pin and the V
IN
pin. Figure
8 shows a circuit that will run only when the input voltage is
present and that protects against a shorted or reversed input.
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Figure 9 shows
the recommended component placement with trace, ground
plane and via locations. Note that large, switched currents
flow in the LT3973’s V
IN
and SW pins, the internal catch
diode and the input capacitor. The loop formed by these
components should be as small as possible. These compo
-
nents, along with the inductor and output capacitor, should
be placed on the same side of the circuit board, and their
connections should be made on that layer. Place a local,
unbroken ground plane below these components. The SW
and BOOST
nodes should be
as small as possible. Finally,
keep the FB nodes small so that the ground traces will shield
them from the SW and BOOST nodes. The exposed pad on
the bottom must be soldered to ground so that the pad acts
as a heat sink. To keep thermal resistance low, extend the
ground plane as much as possible, and add thermal vias
under and near the LT3973 to additional ground planes
within the circuit board and on the bottom side.
Hot Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LT3973 circuits. However, these ca
-
pacitors can cause problems if the LT3973 is plugged into
a live supply. The low loss ceramic capacitor, combined
with stray inductance in series with the power source,
forms an under damped tank circuit, and the voltage at
the V
IN
pin of the LT3973 can ring to twice the nominal
input voltage, possibly exceeding the LT3973’s rating and
damaging the part. If the input supply is poorly controlled
or the user will be plugging the LT3973 into an energized
supply, the input network should be
designed to prevent
this
overshoot. See Application Note 88 for a complete
discussion.
APPLICATIONS INFORMATION
6
8
7
9
10
5
4
2
3
1
VIAS TO LOCAL GROUND PLANE
VIAS TO V
OUT
EN/UVLO
GND
GND
PG
V
OUT
GND
V
IN
3973 F09
High Temperature Considerations
For higher ambient temperatures, care should be taken
in the layout of the PCB to ensure good heat sinking of
the LT3973. The exposed pad on the bottom must be
soldered to a ground plane. This ground should be tied to
large copper layers below with thermal vias; these layers
will spread the heat dissipated by the LT3973. Placing
additional vias can reduce thermal resistance further. The
maximum load current should be derated as the ambient
temperature approaches the maximum junction rating.
Power dissipation within the LT3973 can be estimated by
calculating the total power loss from an efficiency measure
-
ment and subtracting inductor loss. The die temperature
is calculated by multiplying the LT3973 power dissipation
by the thermal resistance from junction to ambient.
Finally, be aware that at high ambient temperatures the
internal Schottky diode will have significant leakage cur
-
rent (see the
Typical Performance Characteristics section)
increasing
the quiescent current of the LT3973 converter.
Other Linear Technology Publications
Application Notes 19, 35 and 44 contain more detailed
descriptions and design information for buck regulators
and other switching regulators. The LT1376 data sheet
has a more extensive discussion of output ripple, loop
compensation and stability testing. Design
Note 100
shows
how to generate a bipolar output supply using a
buck regulator.