REF02EN8

REF-01/REF-02
4
ref012fd
The l denotes the specifi cations which apply over the full operating temperature range, otherwise specifi cations are at T
A
= 25°C.
V
IN
= 15V, –55°C ≤ T
A
≤ ±125°C for REF-01A/REF-02A and REF-01/REF-02, 0°C ≤ T
A
≤ 70°C for REF-01E/REF-02E and
REF-01H/REF-02H, I
L
= 0mA unless otherwise noted.
SYMBOL PARAMETER CONDITIONS
REF-01A/E, REF-02A/E REF-01H/ REF-02H
UNITSMIN TYP MAX MIN TYP MAX
ΔV
ΔT
Output Voltage Change With
Temperature (Notes 4, 5)
C ≤ T
A
≤ 70°C
55°C ≤ T
A
≤ 125°C
l
l
0.02
0.09
0.06
0.15
0.035
0.144
0.17
0.45
%
%
TC Output Voltage Temperature
Coef cient
(Note 6)
l
58.5 8 25ppm/°C
Change in V
O
Temperature
Coeffi cient With Output
Adjustment
R
P
= 10kΩ
l
0.5 0.5 ppm/%
ΔV
OUT
ΔV
IN
Line Regulation
(V
OUT
+ 3V) ≤ V
IN
≤ 33V (Note 2)
C ≤ T
A
≤ 70°C
55°C ≤ T
A
≤ 125°C
l
l
0.0001
0.0001
0.012
0.015
0.0001
0.0001
0.012
0.015
%/V
%/V
ΔV
OUT
ΔI
OUT
Load Regulation
(I
L
= 0mA to 8mA) (Note 2)
C ≤ T
A
≤ 70°C
55°C ≤ T
A
≤ 125°C
l
l
0.002
0.002
0.01
0.012
0.002
0.002
0.012
0.015
%/mA
%/mA
Temperature Voltage Output
Temperature Coef cient
(Note 3) REF-02
l
2.1 2.1 mV/°C
ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS
REF-01C, REF-02C REF-02D
UNITSMIN TYP MAX MIN TYP MAX
ΔV
ΔT
Output Voltage Change With
Temperature
(Notes 4, 5)
l
0.45 1.7 %
TC Output Voltage Temperature
Coef cient
(Note 6)
l
865 8250ppm/°C
Change in V
O
Temperature
Coeffi cient With Output
Adjustment
R
P
= 10kΩ
l
0.5 0.5 ppm/%
ΔV
OUT
ΔV
IN
Line Regulation
(Note 2)
V
IN
= 8V to 30V
l
0.0001 0.018 0.0001 0.05 %/V
ΔV
OUT
ΔI
OUT
Load Regulation
(Note 2)
I
L
= 0mA to 5mA
l
0.002 0.018 0.002 0.05 %/mA
Temperature Voltage Output
Temperature Coef cient
(Note 3) REF-02
l
2.1 2.1 mV/°C
SYMBOL PARAMETER CONDITIONS
REF-01C, REF-02C REF-02D
UNITS
MIN TYP MAX MIN TYP MAX
ΔV
OUT
ΔV
IN
Line Regulation
(Note 2)
(V
OUT
+ 3V) ≤ V
IN
≤ 33V 0.0001 0.015 0.0001 0.04 %/V
ΔV
OUT
ΔI
OUT
Load Regulation
(Note 2)
I
L
= 0mA to 8mA
I
L
= 0mA to 4mA
0.0005 0.015
0.001 0.04
%/mA
%/mA
I
Q
Quiescent Supply Current No Load 0.65 1.6 0.65 2 mA
I
OUT
Load Current
Sink Current
8
–0.2
20
20
8
–0.2
20
20
mA
mA
I
SC
Short-Circuit Current V
O
= 0V 25 25 mA
V
T
Temperature Voltage Output (Note 3) REF-02 Only 620 620 mV
The l denotes the specifi cations which apply over the full operating temperature range, otherwise specifi cations are at T
A
= 25°C.
V
IN
= 15V, 0°C ≤ T
A
≤ 70°C and I
L
= 0mA unless otherwise noted.
V
IN
= 15V, T
A
= 25°C unless otherwise noted.
REF-01/REF-02
5
ref012fd
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Line and load regulation specifi cations include the effect of self
heating.
Note 3: Limit current in or out of Pin 3 to 50nA and capacitance on Pin 3
to 30pF.
Note 4: ΔV is defi ned as the absolute difference between the maximum
output voltage and the minimum output voltage over the specifi ed
temperature range expressed as a percentage of nominal output.
ΔV
V
MAX
V
MIN
V
OUT
=
100
Note 5: ΔV specifi cation applies trimmed or untrimmed.
Note 6: TC is defi ned as ΔV divided by the temperature range, i.e.,
TC
V
T
MAX
T
MIN
=
Δ
Note 7: 0.1Hz to 10Hz noise cannot be 100% tested on modern high speed
test equipment, so Linear Technology does not put a guaranteed maximum
specifi cation on this parameter for standard units. 100% bench testing of
0.1Hz to 10Hz noise is available on special request. To ensure low output
noise, Linear Technology
does
100% test 10Hz to 1kHz noise. Consult
factory for details.
ELECTRICAL CHARACTERISTICS
PACKAGE DESCRIPTION
.050
(1.270)
MAX
.016 – .021**
(0.406 – 0.533)
.010 – .045*
(0.254 – 1.143)
SEATING
PLANE
.040
(1.016)
MAX
.165 – .185
(4.191 – 4.699)
GAUGE
PLANE
REFERENCE
PLANE
.500 – .750
(12.700 – 19.050)
.305 – .335
(7.747 – 8.509)
.335 – .370
(8.509 – 9.398)
DIA
.230
(5.842)
TYP
.027 – .045
(0.686 – 1.143)
.028 – .034
(0.711 – 0.864)
.110 – .160
(2.794 – 4.064)
INSULATING
STANDOFF
45°
H8 (TO-5) 0.230 PCD 0204
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND THE SEATING PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS
.016 – .024
(0.406 – 0.610)
*
**
PIN 1
H Package
8-Lead TO-5 Metal Can (.230 Inch PCD)
(Reference LTC DWG # 05-08-1321)
REF-01/REF-02
6
ref012fd
PACKAGE DESCRIPTION
J8 0801
.014 – .026
(0.360 – 0.660)
.200
(5.080)
MAX
.015 – .060
(0.381 – 1.524)
.125
3.175
MIN
.100
(2.54)
BSC
.300 BSC
(7.62 BSC)
.008 – .018
(0.203 – 0.457)
0° – 15°
.005
(0.127)
MIN
.405
(10.287)
MAX
.220 – .310
(5.588 – 7.874)
12
3
4
8 7
65
.025
(0.635)
RAD TYP
.045 – .068
(1.143 – 1.650)
FULL LEAD
OPTION
.023 – .045
(0.584 – 1.143)
HALF LEAD
OPTION
CORNER LEADS OPTION
(4 PLCS)
.045 – .065
(1.143 – 1.651)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
J8 Package
8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)

REF02EN8

Mfr. #:
Manufacturer:
Analog Devices / Linear Technology
Description:
Voltage References REF02 - Precision Voltage References
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union