3
FN3125.11
October 1, 2015
Absolute Maximum Ratings Thermal Information
Voltage Between Supplies (V+ to V-). . . . . . . . . . . . . . . .44V (22V)
Digital Input Voltage . . . . . . . . . . . . . . . . . . . . . . (V+) +4V to (V-) -4V
Analog Input Voltage . . . . . . . . . . . . . . . . . . (V+) +1.5V to (V-) -1.5V
Typical Derating Factor . . . . . . . . . 1.5mA/MHz Increase in ICCOP
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Operating Conditions
Temperature Range
HI-303-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to 125
o
C
HI-303-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to 75
o
C
HI-303-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40
o
C to 85
o
C
Thermal Resistance (Typical, Note 1)
JA
(
o
C/W)
JC
(
o
C/W)
CERDIP Package. . . . . . . . . . . . . . . . . 80 24
PDIP Package . . . . . . . . . . . . . . . . . . . 90 N/A
SOIC Package . . . . . . . . . . . . . . . . . . . 120 N/A
Maximum Junction Temperature
Ceramic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
o
C
Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
o
C
Maximum Storage Temperature Range . . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300
o
C
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Supplies = +15V, -15V; V
IN
= Logic Input. V
IN
- for Logic “1” = 4V, for Logic “0” = 0.8V.
Unless Otherwise Specified
PARAMETER
TEMP
(
o
C)
-2 -5, -9
UNITSMIN TYP MAX MIN TYP MAX
DYNAMIC CHARACTERISTICS
Switch ON Time, t
ON
25 - 210 300 - 210 300 ns
Switch OFF Time, t
OFF
25 - 160 250 - 160 250 ns
Break-Before-Make Delay, t
OPEN
25 -60- -60-ns
Charge Injection Voltage, V (Note 7) 25 - 3 - - 3 - mV
OFF Isolation (Note 6) 25 - 60 - - 60 - dB
Input Switch Capacitance, C
S(OFF)
25 -16- -16-pF
Output Switch Capacitance, C
D(OFF)
25 -14- -14-pF
Output Switch Capacitance, C
D(ON)
25 -35- -35-pF
Digital Input Capacitance, C
IN
25 - 5 - - 5 - pF
DIGITAL INPUT CHARACTERISTICS
Input Low Level, V
INL
Full - - 0.8 - - 0.8 V
Input High Level, V
INH
(Note 10) Full 4 - - 4 - - V
Input Leakage Current (Low), I
INL
(Note 5) Full - - 1 - - 1 A
Input Leakage Current (High), I
INH
(Note 5) Full - - 1 - - 1 A
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range Full -15 - +15 -15 - +15 V
ON Resistance, r
ON
(Note 2) 25 - 35 50 - 35 50
Full - 40 75 - 40 75
OFF Input Leakage Current, I
S(OFF)
(Note 3) 25 - 0.04 1 - 0.04 5 nA
Full - 1 100 - 0.2 100 nA
OFF Output Leakage Current, I
D(OFF)
(Note 3) 25 - 0.04 1 - 0.04 5 nA
Full - 1 100 - 0.2 100 nA
ON Leakage Current, I
D(ON)
(Note 4) 25 - 0.03 1 - 0.03 5 nA
Full - 0.5 100 - 0.2 100 nA
HI-303
