2
12
2
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Typical Characteristics Data / Specifications and Test Methods
–30
–40 –20 0 20 40 60 80 100
–20 1
0
2
3
–10
0
10
20
30
Temperature (°C)
Capacitance Change (%)
Dissipation Factor (%)
Dissipation Factor
Capacitance
100806040200
–20
–10
0
DC Rated Voltage (%)
Capacitance Change (%)
Capacitance
Frequency (kHz)
1000100101
–6
–4
–2
0
Capacitance Change (%)
0
2
4
6
Dissipation Factor (%)
Capacitance
Dissipation Factor
Temperature Characteristic Typical Voltage Coefficient
Frequency Characteristic
ItemNo Specifications Testing Method
Operating Temperature Range
Capacitance
Temperature Characteristics
Dissipation Factor (D.F.)
Dielectric
Strength
Insulation Resistance (I.R.)
Strength of
Terminal
Life
Humidity
(Under Steady
State)
1
2
3
4
5
6
7
8
9
Between Terminal
Torque Strength
Appearance
Capacitance Change
D.F.
I.R.
Appearance
Capacitance Change
D.F.
I.R.
-20 to +85°C
Within the specified
tolerance.
Temperature coefficient
-4700±1000ppm/°C
(Temp. range: +20 to +85°C)
0.3% max.
No failure.
10000MΩ min.
Capacitor should not be
broken.
No marked defect.
Within ±5%
1.0% max.
1000MΩ min.
No marked defect.
Within ±5%
1.0% max.
1000MΩ min.
The capacitance should be measured at 20°C with 1±0.1kHz
and AC 1 to 5V(r.m.s.).
The capacitance measurement should be made at each step
specified in table.
Capacitance change from the value of step 3 should not exceed the
limit specified.
The dissipation factor should be measured at 20°C with 1±0.1kHz
and AC 1 to 5V(r.m.s.).
The capacitor should not be damaged when DC voltage of 150% of
the rated voltage is applied between the terminals for 60±5 sec. in
insulating liquid or gas.
(Charge/Discharge current V 50mA)
The insulation resistance should be measured with DC1000V within
60±5 sec. of charging.
When mounting the capacitor on equipment, be sure to mount
them within the torque strength values shown in the table below.
Apply a DC voltage of 125% of the rated voltage for 100+24/-0 hrs. in
silicon oil at 85±2°C.
Post-treatment: Capacitor should be stored for 24 hrs. at *room
condition. (Charge/Discharge current V 50mA)
Set the capacitor for 100+24/-0 hrs. at 40±2°C in 90 to 95% relative
humidity. Post-treatment: Capacitor should be stored for 24 hrs. at
*room condition.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Step
Temp. (°C)
1
—
2
—
3
20±2
4
85±2
5
20±2
Terminal Type
ISO M4, No.8-32
torque (N·m)
1.5
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
!Note
C41E2.pdf 03.4.16
