10
Notes:
1. Bypassing of the power supply line is
required with a 0.1 µF ceramic disc
capacitor adjacent to each optocoupler, as
illustrated in Figure 15. Total lead length
between both ends of the capacitor and
the isolator pins should not exceed 10 mm.
2. Peaking circuits may produce transient
input currents up to 50 mA, 50 ns maximum
pulse width, provided average current does
not exceed 20 mA.
3. Device considered a two terminal device:
pins 1 , 2, 3, and 4 shorted together, and
pins 5, 6, 7, and 8 shorted together.
4. The t
PLH
propagation delay is measured
from the 50% point on the trailing edge of
the input pulse to the 1.5 V point on the
trailing edge of the output pulse.
5. The t
PHL
propagation delay is measured
from the 50% point on the leading edge of
the input pulse to the 1.5 V point on the
leading edge of the output pulse.
6. t
PSK
is equal to the worst case difference in
t
PHL
and/or t
PLH
that will be seen between
units at any given temperature within the
operating condition range.
7. CM
H
is the maximum tolerable rate of rise
of the common mode voltage to assure
that the output will remain in a high logic
state (i.e., V
OUT
> 2.0 V).
8. CM
L
is the maximum tolerable rate of fall
of the common mode voltage to assure
that the output will remain in a low logic
state (i.e., V
OUT
< 0.8 V). This specification
assumes that good board layout proce-
dures were followed to reduce the
effective input/output capacitance as
shown in Figure 15.
9. In accordance with UL and CSA
requirements, each optocoupler is proof
tested by applying an insulation test
voltage ≥ 5000 Vrms for one second
(leakage detection current limit,
I
I-O
≤ 5 µA).
10. AC performance at I
F
= 4 mA is
approximately equivalent to the HCPL-
2601/11 at I
F
= 7.5 mA for comparison
purposes.
Figure 2. Low level output voltage vs.
temperature.
Figure 1. High level output current vs.
temperature.
Figure 3. Typical input forward current vs.
input forward voltage.
Figure 5. Input threshold current vs.
temperature.
Figure 6. Low level output current vs.
temperature.
Figure 4. Output voltage vs. forward input
current.
15
10
5
0
-60 -40 -20 0 20 40
60 80
100
V
CC
= 5.5 V
V
O
= 5.5 V
V
IN
= 0.8 V
I
OH
– HIGH LEVEL OUTPUT CURRENT – µA
T
A
– TEMPERATURE – °C
-60 -40 -20 0 20 40 60 80 100
V
CC
= 5.5 V
I
F
= 2 - 4 mA
T
A
– TEMPERATURE – °C
V
OL
– LOW LEVEL OUTPUT VOLTAGE – V
0.3
0.4
0.5
I
O
= 13.0 mA
I
O
= 16.0 mA
0.2
0.6
0.8 1.0 1.2 1.4 1.6 1.8
V
F
– INPUT FORWARD VOLTAGE – V
I
F
– INPUT FORWARD CURRENT – A
T
A
= 85° C
T
A
= 25° C
10
-1
10
-2
10
-3
10
-4
10
-5
10
-6
2.0
T
A
= -40° C
5.0
4.0
2.0
0
00.51.0
1.5
2.0
I
F
– FORWARD INPUT CURRENT – mA
V
O
– OUTPUT VOLTAGE – V
3.0
1.0
R
L
= 350 Ω
R
L
= 1 kΩ
R
L
= 4 kΩ
2.0
1.5
0.5
0
-60 -40 -20 0 20 40 60 80 100
T
A
– TEMPERATURE – °C
I
TH
– INPUT THRESHOLD CURRENT – mA
1.0
V
CC
= 5.0 V
V
O
= 0.6 V
I
O
= 13.0 mA
2.5
50
45
35
30
-50 -30 -10 10 30 50 70 90
T
A
– TEMPERATURE – °C
I
OL
– LOW LEVEL OUTPUT CURRENT – mA
40
55
V
CC
= 5 V
V
OL
= 0.6 V
I
F
= 4 mA
I
F
= 2 mA
0
