OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TLP705(TP,F)

P1-P3P4-P6
TLP705
2014-09-22
1
Unit: mm
Weight: 0.26 g (typ.)
4.58±0.25
4.0
+0.25
−0.20
9.7±0.3
6.8±0.25
0.4±0.1
1.27±0.2 1.25±0.25
7.62±0.25
3.65
+0.15
−0.25
0.25±
1 2 3
6 5 4
11-5J1
TOSHIBA 11-5J1
−0.05
+0.10
TOSHIBA Photocoupler GaAℓAs IRED + Photo IC
TLP705
Plasma Display Panel
Industrial Inverter
IGBT/Power MOS FET Gate Drive
TLP705 consists of a GaAℓAs light emitting diode and an integrated
photodetector.
This unit is 6-lead SDIP package. TLP705 is 50% smaller than 8pin DIP and
has suited the safety standard reinforced insulation class.
So mounting area in safety standard required equipment can be reduced.
TLP705 is suitable for gate driving circuit of IGBT or power MOS FET.
Especially TLP705 is capable of “direct” gate drive of lower Power IGBTs.
• Peak output current : ±0.45 A (max)
• Operating frequency : 250kHz (max)
• Guaranteed performance over temperature : −40 to 100°C
• Supply current : 3mA (max)
• Power supply voltage : 10 to 20 V
• Threshold input current : I
FLH
= 8 mA (max)
• Switching time (t
pLH
/ t
pHL
) : 200 ns (max)
• Common mode transient immunity :±10 kV/μs (min)
• Isolation voltage : 5000 Vrms (min)
• UL Recognized :UL1577, File No.E67349
• Construction Mechanical Rating
7.62-mm pitch
standard type
10.16-mm pitch
TLPXXXF type
Creepage Distance
Clearance
Insulation Thickness
7.0 mm (min)
7.0 mm (min)
0.4 mm (min)
8.0 mm (min)
8.0 mm (min)
0.4 mm (min)
• Option (D4)
TÜV approved
: EN60747-5-2
Certificate No. R50033433
Maximum operating insulation voltage
: 890 Vpk
Highest permissible over voltage : 8000 V
pk
(Note) When a EN60747-5-2 approved type is needed,
please designate the “Option(D4)”
Truth Table
Input LED
Tr1 Tr2 Output
H ON ON OFF H
L
OFF OFF ON L
A
0.1 μF bypass capacitor must be connected
between pins 6 and 4. (See Note 6)
1+
3−
V
CC
V
O
GND
(Tr1)
(Tr2)
I
CC
I
O
I
F
V
F
6
5
4
SHIELD
1: ANODE
2: NC
3: CATHODE
4: GND
5: V
O
(OUTPUT)
6: V
CC
1
3
5
6
2
SHIELD
Pin Configuration (Top View)
Schematic
Start of commercial production
2004/04
TLP705
2014-09-22
2
Absolute Maximum Ratings
(Ta
=
25°C)
Characteristics Symbol Rating Unit
LED
Forward current I
F
20 mA
Forward current derating (Ta ≥ 85°C) ΔI
F
/ΔTa −0.54 mA/°C
Peak transient forward current (Note 1) I
FP
1 A
Reverse voltage V
R
5 V
Junction temperature T
j
125 °C
Detector
“H” peak output current (Note 2) I
OPH
−0.45 A
“L” peak output current (Note 2) I
OPL
0.45 A
Output voltage V
O
25 V
Supply voltage V
CC
25 V
Junction temperature T
j
125 °C
Operating frequency (Note 3) f 250 kHz
Storage temperature range T
stg
−55 to 125 °C
Operating temperature range T
opr
−40 to 100 °C
Lead soldering temperature (10 s) (Note 4) T
sol
260 °C
Isolation voltage (AC, 1 minute, R.H. ≤ 60%) (Note 5) BV
S
5000 Vrm s
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if
the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc.).
Note 1: Pulse width P
W
≤ 1μs, 300 pps
Note 2: Exponential waveform pulse width P
W
≤ 2 μs, f ≤15 kHz
Note 3: Exponential waveform I
OPH
≤-0.25 A (≤80 ns), I
OPL
≤+0.25 A (≤80 ns), Ta =100 °C
Note 4: It is effective soldering area of Lead.
Note 5: Device considered a two terminal device: pins 1, 2 and 3 shorted together, and pins 4, 5 and 6 shorted
together.
Note 6: A ceramic capacitor (0.1 μF) should be connected from pin 6 to pin 4 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypassing may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
Recommended Operating Conditions
Characteristics Symbol Min Typ. Max Unit
Input current, ON (Note 7) I
F (ON)
10 ⎯ 15 mA
Input voltage, OFF V
F (OFF)
0 ⎯ 0.8 V
Supply voltage V
CC
10 ⎯ 20 V
Peak output current I
OPH
/ I
OPL
⎯ ⎯ ± 0.15 A
Operating temperature T
opr
- 40 ⎯ 100 °C
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Note 7: Input signal rise time (fall time) < 0.5 μs.
Note 8: If the rising slope of the supply voltage (V
CC
) for the detector is steep, stable operation of the internal circuits
cannot be guaranteed.
Be sure to set 3.0V/μs or less for a rising slope of the V
CC
.
TLP705
2014-09-22
3
Electrical Characteristics
(Ta
=
−
40 to 100°C, unless otherwise specified)
Characteristics Symbol
Test
Circuit
Test Condition Min Typ.* Max Unit
Forward voltage V
F
⎯ I
F
= 10 mA, Ta = 25°C ⎯ 1.6 1.8 V
Temperature coefficient of forward
voltage
∆V
F
/∆Ta ⎯ I
F
= 10 mA ⎯ −2.0 ⎯ mV/°C
Input reverse current I
R
⎯ V
R
= 5 V, Ta = 25°C ⎯ ⎯ 10 μA
Input capacitance C
T
⎯ V = 0 V , f = 1 MHz,Ta = 25°C ⎯ 45 ⎯ pF
Output current
(Note 9
)
“H” Level
I
OPH1
1
V
CC
= 15 V
I
F
= 10 mA
V
6-5
= 4 V −0.15 −0.35 ⎯
A
I
OPH2
V
6-5
= 10 V
−0.3 −0.6
⎯
“L” Level
I
OPL1
2
V
CC
= 15 V
I
F
= 0 mA
V
5-4
= 2 V 0.15 0.36 ⎯
I
OPL2
V
5-4
= 10 V
0.3 0.62
⎯
Output voltage
“H” Level V
OH
3
V
CC
= 10 V
I
O
= −100 mA,
I
F
= 10 mA
6.0 8.5 ⎯
V
“L” Level V
OL
4
I
O
= 100 mA,
V
F
= 0.8 V
⎯ 0.4 1.0
Supply current
“H” Level I
CCH
5
V
CC
= 10 to 20 V
V
O
open
I
F
= 10 mA ⎯ 2.0 3.0
mA
“L” Level I
CCL
6 I
F
= 0 mA ⎯ 2.0 3.0
Threshold input current L → H I
FLH
⎯ V
CC
= 15 V, V
O
> 1 V ⎯ 2.5 8 mA
Threshold input voltage H → L V
FHL
⎯ V
CC
= 15 V, V
O
< 1 V 0.8 ⎯ ⎯ V
Supply voltage V
CC
⎯ ⎯ 10 ⎯ 20 V
*: All typical values are at Ta = 25°C
Note 9: Duration of I
O
time ≤ 50 μs
Note10: This product is more sensitive than the conventional product to static electricity (ESD) because of a lowest
power consumption design.
General precaution to static electricity (ESD) is necessary for handling this component.
Isolation Characteristics
(Ta = 25°C)
Characteristic Symbol Test Condition Min Typ. Max Unit
Capacitance input to output C
S
V = 0 V, f = 1MHz (Note 5) ― 1.0 ― pF
Isolation resistance R
S
R.H. ≤ 60%, V
S
= 500V
(Note 5)
1×10
12
10
14
― Ω
Isolation voltage BV
S
AC, 1 minute 5000 ― ―
Vrms
AC, 1 second, in oil ― 10000 ―
DC, 1 minute, in oil ― 10000 ― Vdc
P1-P3P4-P6

TLP705(TP,F)

Mfr. #:
Buy TLP705(TP,F)
Manufacturer:
Description:
Logic Output Optocouplers IC Cplr IGBT drive IFLH=5mA
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet