VY1 Compact Series
www.vishay.com
Vishay BCcomponents
Revision: 16-Jan-17
6
Document Number: 28555
For technical questions, contact: cdc@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PERFORMANCE
TEST TEST CONDITION TEST LIMITS
Visual and mechanical
inspection
Optical inspection, dimensions measured with caliper No visible damage, marking legible
Capacitance (C) 25 °C ± 3 °C , relative humidity (RH) 75 %,
1.0 V
RMS
± 0.2 V
RMS
at 1 kHz
Capacitance within specified tolerance
Dissipation factor (DF) DF 2.5 %
Insulation resistance (IR) Measured within 60 s ± 5 s after charging at 500 V
DC
10 000 M min.
Dielectric strength 4000 V
AC
at 50 Hz/60 Hz for 1 min, 50 mA max. No failure
Temperature
characteristic
RH 75 %, 1.0 V
RMS
± 0.2 V
RMS
at 1 kHz +22 % / -56 %
Impulse voltage Pulse voltage: 10 kV
Pulses per polarity: 10
Polarity: ± (both)
Time between pulses of same polarity: 20 s
Time between pulses of different polarity: 30 s
No failure
Life test 1000 h at 125 °C ± 2 °C, 850 V
AC
/ 50 Hz;
once every hour 1000 V
AC
for 0.1 s
External appearance: no visible damage
C/C ± 15 %
DF 5 %
IR 3000 M
Dielectric strength: no failure
Damp heat test
(85 / 85 / 1000 h)
1000 h + 48 h / - 0 h at 85 % relative humidity, 85 °C ± 3 °C,
loading voltage: 760 V
AC
No failure
Humidity test 500 h at 500 V
AC
, 50 Hz and 500 h unloaded
40 °C, RH = 90 % to 95%
External appearance: no visible damage
C/C ± 15 %
DF 5 %
IR 3000 M
Dielectric strength: no failure
Robustness of
termination
Pull test: 0.5 kg tensile weight in radial direction for 10 s ± 1 s
Bending strength: capacitor body rotated by 90° in both directions
No damage to capacitor body and lead wire
Soldering effect Immersion of lead wires into 260 °C ± 5 °C solder for 10 s ± 2 s;
min. distance from body: 1.5 mm
Hand soldering at 400 °C ± 10 °C for 3 s to 4 s;
min. distance from body: 1.5 mm
External appearance: no visible damage
C/C ± 10 %
Dielectric strength: no failure
Vibration test
Solder the capacitor onto test jig (glass epoxy body) and use resin
(adhesive) to stick the body to the test jig.
The capacitor must be soldered firmly to the supporting lead wire.
Vibration change from 10 Hz to 2000 Hz and back to 10 Hz;
Total amplitude: 1.5 mm; Acceleration: 100 m/s
2
;
Sweep rate: 1 oct/min, each axis 2 h (6 h in total)
External appearance: no visible damage
Capacitance within specified tolerance
DF 2.5 %
IR 10 000 G