OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HA5023IBZ

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17
1
HA5023
Dual 125MHz Video Current
Feedback Amplifier
The HA5023 is a wide bandwidth high slew rate dual
amplifier optimized for video applications and gains between
1 and 10. It is a current feedback amplifier and thus yields
less bandwidth degradation at high closed loop gains than
voltage feedback amplifiers.
The low differential gain and phase, 0.1dB gain flatness, and
ability to drive two back terminated 75cables, make this
amplifier ideal for demanding video applications.
The current feedback design allows the user to take
advantage of the amplifier’s bandwidth dependency on the
feedback resistor. By reducing R
F
, the bandwidth can be
increased to compensate for decreases at higher closed
loop gains or heavy output loads.
The performance of the HA5023 is very similar to the
popular Intersil HA-5020
.
Features
• Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz
• Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/s
• Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . 800V
• Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03%
• Differential Phase. . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03°
• Supply Current (per Amplifier) . . . . . . . . . . . . . . . . 7.5mA
• ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V
• Guaranteed Specifications at 5V Supplies
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• Video Gain Block
• Video Distribution Amplifier/RGB Amplifier
• Flash A/D Driver
• Current to Voltage Converter
• Medical Imaging
• Radar and Imaging Systems
• Video Switching and Routing
Pinout
HA5023
(PDIP, SOIC)
TOP VIEW
Ordering Information
PART NUMBER
PART
MARKING
TEMP.
RANGE
(°C) PACKAGE
PKG.
DWG. #
HA5023IPZ
(Note) (No
longer
available,
recommended
replacement:
HA5023IBZ)
HA5023IPZ -40 to 85 8 Ld PDIP*
(Pb-free)
E8.3
HA5023IBZ
(Note)
5023IBZ -40 to 85 8 Ld SOIC
(Pb-free)
M8.15
HA5023IBZ96
(Note)
5023IBZ -40 to 85 8 Ld SOIC
Tape and Reel
(Pb-free)
M8.15
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
OUT1
-IN1
+IN1
V-
1
2
3
4
8
7
6
5
V+
OUT2
-IN2
+IN2
+
-
+
-
Data Sheet September 30, 2015 FN3393.9
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas LLC
Copyright Intersil Americas LLC 1998, 2005-2006, 2015. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
2
FN3393.9
September 30, 2015
Absolute Maximum Ratings Thermal Information
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . .36V
DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . V
SUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V
Output Current (Note 4) . . . . . . . . . . . . . . . . .Short Circuit Protected
ESD Rating (Note 3)
Human Body Model (Per MIL-STD-883 Method 3015.7). . . 2000V
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . 4.5V to 15V
Thermal Resistance (Typical, Note 2)
JA
(°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C
Maximum Junction Temperature (Plastic Package, Note 1) . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder process-
ing only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175°C for die, and below 150°C
for plastic packages. See Application Information section for safe operating area information.
2.
JA
is measured with the component mounted on an evaluation PC board in free air.
3. The non-inverting input of unused amplifiers must be connected to GND.
4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)
output current should not exceed 15mA for maximum reliability.
Electrical Specifications V
SUPPLY
= 5V, R
F
= 1k A
V
= +1, R
L
= 400 C
L
10pF, Unless Otherwise Specified
PARAMETER TEST CONDITIONS
(NOTE 9)
TEST
LEVEL
TEMP.
(°C) MIN TYP MAX UNITS
INPUT CHARACTERISTICS
Input Offset Voltage (V
IO
)A25-0.83mV
AFull--5mV
Delta V
IO
Between Channels A Full - 1.2 3.5 mV
Average Input Offset Voltage Drift B Full - 5 - V/°C
V
IO
Common Mode Rejection Ratio Note 5 A 25 53 - - dB
A Full 50 - - dB
V
IO
Power Supply Rejection Ratio 3.5V V
S
6.5V A 25 60 - - dB
AFull55-- dB
Input Common Mode Range Note 5 A Full 2.5 - - V
Non-Inverting Input (+IN) Current A 25 - 3 8 A
AFull--20A
+IN Common Mode Rejection
(+I
BCMR
= )
Note 5 A 25 - - 0.15 A/V
AFull--0.5A/V
+IN Power Supply Rejection 3.5V V
S
6.5V A 25 - - 0.1 A/V
AFull--0.3A/V
Inverting Input (-IN) Current A 25, 85 - 4 12 A
A-40-1030A
Delta -IN BIAS Current Between Channels A 25, 85 - 6 15 A
A-40-1030A
1
+R
IN
HA5023
3
FN3393.9
September 30, 2015
-IN Common Mode Rejection Note 5 A 25 - - 0.4 A/V
AFull--1.0A/V
-IN Power Supply Rejection 3.5V V
S
6.5V A 25 - - 0.2 A/V
AFull--0.5A/V
Input Noise Voltage f = 1kHz B 25 - 4.5 - nV/Hz
+Input Noise Current f = 1kHz B 25 - 2.5 - pA/Hz
-Input Noise Current f = 1kHz B 25 - 25.0 - pA/Hz
TRANSFER CHARACTERISTICS
Transimpedence Note 11 A 25 1.0 - - M
AFull0.85--M
Open Loop DC Voltage Gain R
L
= 400, V
OUT
= 2.5V A 25 70 - - dB
AFull65-- dB
Open Loop DC Voltage Gain R
L
= 100, V
OUT
= 2.5V A 25 50 - - dB
AFull45-- dB
OUTPUT CHARACTERISTICS
Output Voltage Swing R
L
= 150 A 25 2.5 3.0 - V
AFull2.5 3.0 - V
Output Current R
L
= 150 BFull16.6 20.0 - mA
Output Current, Short Circuit V
IN
= 2.5V, V
OUT
= 0V A Full 40 60 - mA
POWER SUPPLY CHARACTERISTICS
Supply Voltage Range A 25 5 - 15 V
Quiescent Supply Current A Full - 7.5 10 mA/Op Amp
AC CHARACTERISTICS (A
V
= +1)
Slew Rate Note 6 B 25 275 350 - V/s
Full Power Bandwidth Note 7 B 25 22 28 - MHz
Rise Time Note 8 B 25 - 6 - ns
Fall Time Note 8 B 25 - 6 - ns
Propagation Delay Note 8 B 25 - 6 - ns
Overshoot B25-4.5- %
-3dB Bandwidth V
OUT
= 100mV B 25 - 125 - MHz
Settling Time to 1% 2V Output Step B 25 - 50 - ns
Settling Time to 0.25% 2V Output Step B 25 - 75 - ns
Electrical Specifications V
SUPPLY
= 5V, R
F
= 1k A
V
= +1, R
L
= 400 C
L
10pF, Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
(NOTE 9)
TEST
LEVEL
TEMP.
(°C) MIN TYP MAX UNITS
HA5023
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17

HA5023IBZ

Mfr. #:
Buy HA5023IBZ
Manufacturer:
Renesas / Intersil
Description:
Operational Amplifiers - Op Amps W/ANNEAL OPAMP 2X 12 5MHZ VID IND
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet