D1U-W-1600-12-Hx Series
AC/DC Front End Power Supply
CPS_D1U-W-1600-12-Hx.E01 Page 1 of 5
www.murata-ps.com
For full details go to
www.murata-ps.com/rohs
SELECTION GUIDE
Part Number
Power Output
High Line AC
Power Output
Low Line AC
Main Output
Standby
Output
Airflow
D1U-W-1600-12-HC2C 1600W 1200W 12V 3.3V Back to front
D1U-W-1600-12-HA2C 1600W 1200W 12V 5V Back to front
D1U-W-1600-12-HC1C 1600W 1200W 12V 3.3V Front to back
D1U-W-1600-12-HA1C 1600W 1200W 12V 5V Front to back
INPUT CHARACTERISTICS
Parameter Conditions Min. Typ. Max. Units
Input Voltage Operating Range 90 115/230 264 Vac
Input Frequency 47 50/60 63 Hz
Turn-on Input Voltage Ramp up 78.5 86.5
Vac
Turn-off Input Voltage Ramp down 70.5 78
Maximum Input Current
Low Line AC 90Vac 15
Arms
High Line AC 180Vac 10
Inrush Current Cold start between 0-1msec 100 Apk
Power Factor
Output load >90% 95%
Output load >50% 75%
OUTPUT VOLTAGE CHARACTERISTICS
Output
Voltage
Parameter Conditions Min. Typ. Max. Units
12V
Voltage Set Point Accuracy 12.12
Vdc
Line and Load Regulation 11.75 12.48
Ripple Voltage & Noise
1
20MHz Bandwidth 120 mV p-p
Output Current 0 131.6 A
Load Capacitance 40000 µF
3.3Vsb
Voltage Set Point Accuracy 3.3
Vdc
Line and Load Regulation 3.2 3.4
Ripple Voltage & Noise
1
20MHz Bandwidth 33 mV p-p
Operating Range 0 6 A
Load Capacitance 1530 µF
5Vsb
Voltage Set Point Accuracy 5
Vdc
Line and Load Regulation 4.85 5.15
Ripple Voltage & Noise
1
20MHz Bandwidth 50 mV p-p
Operating Range 0 4 A
Load Capacitance 1530 µF
FEATURES
nRoHS compliant
n1600W (220Vac), 1200W (110Vac)
Output power
n12V Main output,
3.3V or 5V standby output
n1U sized; dimensions 4.75"x12.00"x1.61"
n17.5 Watts per cubic inch density
nN+1 redundancy capable,
including hot-docking
nActive current sharing on main output
nOver-voltage, over-current,
over-temperature protection
nInternal cooling fans
nI²C Bus Interface with status indicators
PRODUCT OVERVIEW
The D1U-W-1600 is a 1600 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant
systems. The main output is 12V and standby output of either 5V or 3.3V. Packaged in 1U low profile, it is designed
to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture
systems requiring high power density. The highly efficient electrical and thermal design with internal cooling fans
supports reliable operation conditions. The D1U-W-1600 is designed to auto-recover from over-temperature faults.
Status information is provided with front panel LEDs, logic signals and I
2
C management interface. Three units can be
packaged into a 19" 1U power shelf to provide up to 4.8kW of power.
1
Ripple and noise are measured with 0.1 uF of ceramic capacitance and 2 x 270 uF of OSCON capacitance on each
of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial
cable with 50ohm scope termination is used. See Ripple Test Setup diagram.