SERIES 19
2” Diameter, 15 Amp
FEATURES
• UL Recognized
• Rugged Construction
• Choice of Termination
Solder Lug Terminals
‘Faston’ Terminals
All dimensions not shown are the same as
the Solder Lug Terminals.
Grayhill part number and date code marked on label. Customer part number marked on request.
DIMENSIONS In inches (and millimeters)
1.687
± .030
(42,85
± 0,76)
DIA.
3/8-32 UNEF-2A THREAD
.950
± .060
(24,13
± 1,52)
.375 ± .020
(9,53 ± 0,51)
.500 ± .020
(12,7 ± 0,51)
BUSHING KEYWAY
.066 ± .003 WIDE
(1,68 ± 0,08)
.036 ± .005 DEEP
(0,91 ± 0,13)
.344 ± .010
(8,74 ± 0,25)
.250 ± .005
(6,35 ± 0,13) DIA.
HEX MTG NUT
9/16 ± .010 (14,29 ± 0,25)
ACROSS FLATS
3/32 ± .010 (2,38 ± 0,25)
THICK
.88
(22,4)
2.00
(50,8)
SOLDER TERMINALS
WIRE HOLE .125 (3,18)
1.687
± .030
(42,85
± 0,76)
DIA.
.88
(22,4)
2.28
(57,91)
DIA.
FOR AMP .250 SERIES
OR EQUIVALENT
WIRE HOLE .080" (2,03)
.219 ± .005
(5,56 ± 0,15)
SPECIFICATIONS
Electrical Rating
Rated: UL Recognition: File Number E35289
15 Amps, 120 Vac, non-inductive load.
One Amp, 120 Vdc, non-inductive load.
Additional Grayhill Rating: 7.5 Amps, 220 Vac,
non-inductive load.
This rating is based on the following criteria:
Overload—50 operations at 125% rated ac load
and 150% rated DC load.
Endurance—6000 operations at rated load
with 900 Vac dielectric strength before and
after test.
Temperature Rise—Not to exceed 30°C when
carrying rated ac load after endurance test.
Contacts will carry 20 Amps at 115 volts AC with
30°C maximum temperature rise.
Contact Resistance: (Measured at 2 Vdc
and approximately 100 mA) for new switch
approximately 10 milliohms.
Insulation Resistance: Approximately 100,000
Mohms. Between mutually insulated parts.
Voltage Breakdown: Approximately 2500 Vac
between mutually insulated parts.
Materials and Finishes
Rotor Contact: Silver alloy
Stator Contact: Silver alloy
Shaft: 303 Stainless steel
Stop Rivet: Steel, tin/zinc-plated
Mounting Bushing: Brass, tin/zinc-plated
Base and Drive Hub: Heat resistant, electrical
grade phenolic.
Mounting Nut: Brass, tin/zinc-plated or stain-
less steel.
Detent Mechanism: Brass, silver-plated
“Faston” Terminal: Brass, silver-plated
Solder Terminal: Brass, silver-plated
Mounting Hardware: One mounting nut
9
/16"
across flats,
3
/32" thick and one non-turn washer
(see detail) are supplied with each switch.
Additional Characteristics
Single Pole, Single Deck: 2 to 11 positions
plus common 30° Indexing.
Contacts: Non-shorting type
Stops: A rivet provides the fixed stop on all
switches. Minimum number of positions is 2,
and maximum is 11. Terminal 12, the common,
is isolated from rotation.
Rotational Torque: 12 to 36 ounch-
inches on average for new switches.
Contact Force: Approximately 12 ounces
Shaft Flat Orientation: Opposite point of contact
(see circuit diagram).
Circuit Diagram viewed from
shaft end with switch in position #1
Non-Turn Washer Detail
.625 ± .010
(15,88 ± 0,25)
DIA.
.187 ± .003
(4,75 ± 0,08)
.500 ± .005
(12,7 ± 1,27)
.060 ± .010
(1,52 ± 0,25)
.093 + .015/ – .000
(2,36 + 0,38/ – 0,00)
.025 ± .002
(0,64 ± 0,05)
ACCESSORIES
Non-Turn Washer
Brass, tin/zinc-plated washer, detailed above
may be purchased as a separate item.
Part No. 19C1014.
ORDERING INFORMATION
Part Numbers: Designate as follows, using the
2 digits after the dash to indicate the number
of positions.
For Faston Terminal:
Use 19101-02UL through 19101-11UL
For Solder Terminal:
Use 19001-02UL through 19001-11UL
Specials: Not available through Distributors. For
special shafts, bushings, etc. contact Grayhill.
12 (COMMON)
3
5
7
8
9
10
2
4
6
1
11
OF BUSHING
KEYWAY
Available from your local Grayhill Distributor.
For prices and discounts, contact a local Sales Office, an authorized local Distributor or Grayhill.
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
Rotary Switches
Single Deck Rotary Switches
