Step 1. Install the batteries on the 1320x-QE128-EVB development
boards. Note the board names on the back of the boards: “Dimmable
Light” and “Dimmer Switch”.
Step 2. Power on the Dimmable Light board using the slide switch SW1.
LED1 blinks to indicate that the node has not formed a ZigBee Network.
The LCD displays “HaDimmableLight” on line 1 and “Cfg” on line 2 of
the LCD.
Step 3. On the Dimmable Light board, press SW2 to start the process
of forming the ZigBee Network. The Dimmable Light board LEDs flash
and the LCD briefly displays “Starting Network”. When the network is
formed, LED1 and LED2 are on. LED1 indicates the network is formed
and LED2 indicates that it is ready to allow other nodes to join the
network. The LCD displays “Running Device” on line 1, and on line 2
displays “Cfg” and the PAN short address “0000”.
Step 4. Power on the Dimmer Switch board using the slide switch SW1.
LED1 blinks to indicate that the Dimmer Switch has not joined a ZigBee
Network. The LCD displays “HaDimmer Switch” on line 1 and on line 2
displays “Cfg”.
Step 5. On the Dimmer Switch board, press SW2 to start the process
of joining the ZigBee Network. The Dimmer Switch board LEDs flash
and the LCD briefly displays “Joining Network”. When it has joined the
network, LED1 is on to indicate it has successfully joined the network.
The LCD displays “Running Device” on line 1 and on line 2 displays
“Cfg” and the PAN short address “796F”.
Step 6. Press SW4 on each board to bind them in the network. On both
boards, LED3 blinks and the LCD displays “Binding” until the binding
process is complete. Once binding is complete, LED3 on both boards
stays on and both LCDs display “Binding Success” on line 1.
Step 7. To place each board in Application Mode, press and hold SW2
on each board for at least 2 seconds. All LEDS on both boards turn off,
and on line 2 of both LCDs, “Cfg” changes to “App”.
Step 8. Now users can control the Dimmable Light board using the
Dimmer Switch board. Pressing SW3 from 1 to 3 times on the Dimmer
Switch board turns on LEDs 2 through 4 on the Dimmable Light board.
Pressing SW2 from 1 to 4 times on the Dimmer Switch board turns off
LEDs 4 through 2 on the Dimmable Light board. Line 1 on the Dimmable
Light LCD displays “Level = “ to indicate the current level of light, or
“Light Off”.
Step 9. Recommended Reading:
Instructions on how to run BeeKit are contained in the BeeKit Wireless
Connectivity ToolKit Quick Start Guide (BKWCTKQSG) and the BeeKit
Wireless Connectivity ToolKit User’s Guide (BKWCTKUG).
Instructions on how to run the SMAC demonstration applications are
contained in the Running SMAC Demonstration Operations Application
Note (AN3231).
Instructions on how to run the MAC demonstration application
are contained in the 802.15.4 Media Access Controller (MAC)
MyStarNetworkworkApp User’s Guide (802154MSNAUG) and the
802.15.4 Media Access Controller (MAC) MyWirelessApp User’s Guide
(802154MWAUG).
Instructions on how to run the ZigBee demonstration applications that
come with BeeStack are contained in the ZigBee Applications User’s
Guide (ZAUG). To start developing custom BeeStack applications, see
the BeeStack Application Development Guide (BSADG).
Hardware Setup
Freescale and the Freescale logo are trademarks or registered trademarks of Freescale
Semiconductor, Inc. in the U.S. and other countries. All other product or service names are the
property of their respective owners. © Freescale Semiconductor, Inc. 2008
Document Number: QE128DKSQSK / REV 0
Learn More:
For more information about
Freescale products, please visit
www.freescale.com.
