Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Surface Mount
NPCAP
TM
-PXKSeries
・
Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
・
Rated voltage range : 2.5 to 16V
dc
, Capacitance range : 100 to 560µF
・
Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
・
RoHS Compliant
・
Halogen Free
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range
2.5 to 16V
dc
Capacitance Tolerance
±
20% (M) (at 20
℃
, 120Hz)
Surge Voltage Rated voltage
×
1.15V (at 105
℃
)
Leakage Current Shall not exceed values shown in STANDARD RATINGS. (at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
0.12 max.
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(-25
℃
)/Z(+20
℃
)
≦
1.15
Z(-55
℃
)/Z(+20
℃
)
≦
1.25
(at 100kHz)
Endurance The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 2,000 hours
(F46 : 1,000 hours) at 105
℃
.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
DF (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Bias Humidity The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to the DC rated voltage at
60
℃
, 90 to 95% RH for 1,000 hours (F46 : 500hours).
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
DF (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
through a protective resistor(R=1k
Ω
) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
DF (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105℃.
◆
DIMENSIONS [mm]
L
±
0.3 (Note)
0.3max.
A
±
0.2
W
B
±
0.2
C
±
0.2
P
Note : L+0.1/-0.2 for F46
Size Code
E61
F46
F61
φ
D
5
6.3
6.3
L
5.8
4.5
5.8
A
5.3
6.6
6.6
B
5.3
6.6
6.6
C
5.9
7.2
7.2
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
P
1.4
1.9
1.9
●Terminal Code : A
◆
PART NUMBERING SYSTEM
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 330µF:331, 560µ
F:561)
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 6.3V:6R3)
Series code
Category
A P X K A R A GM
1 3 42 6 7 8 9 10 13125 18171611 1514
Please refer to "Product code guide (conductive polymer type)"
Downsized
PXK
PXE P36
◆
MARKING
K
89A
330
2.5
V
30
CAT. No. E1001N
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
