1-406375-0 Datasheet 1-406375-0 | P1-P3

Product

Specification

108-1389

11Mar11 Rev B

Jack, Modular, 110 Panel Mount

1. SCOPE

1.1. Content

This specification covers performance, tests and quality requirements for TE Connectivity (TE) Category

3 and Category 5 110 panel mount modular jacks. These assemblies are designed for panel mounting

and provide insulation displacing 110 punchdown blocks for terminating both shielded and unshielded

twisted pair conductors to the jacks. 110 blocks are designed to terminate 22 to 26 AWG solid or

stranded conductors having a maximum overall diameter of .050. Jacks are available in fully shielded,

unshielded and grounded styles.

1.2. Qualification

When tests are performed on subject product line, procedures specified in 109 Series Test

Specifications shall be used. All inspections shall be performed using applicable inspection plan and

product drawing.

2. APPLICABLE DOCUMENTS

The following documents constitute a part of this specification to the extent specified herein. In the

event of conflict between requirements of this specification and product drawing, product drawing shall

take precedence. In the event of conflict between requirements of this specification and referenced

documents, this specification shall take precedence.

2.1. TE Documents

! 109-1: General Requirements For Test Specifications

! 109 Series: Test Specifications as indicated in Figure 1

! 108-1588: Product Specification (110 Connection Block)

! 408-3354: Instruction Sheet (110 Panel Mount Jack)

! 501-202: Qualification Test Report

2.2. Commercial Specifications

! EIA/TIA-TSB40-A: Transmission Specifications for Unshielded Twisted Pair Connecting Hardware

! FCC Rules For Registration Of Telephone Equipment, Part 68, Subpart F, Connectors

! UL File E81956 Volume 1, Section 12: Communication Circuit Accessories

3. REQUIREMENTS

3.1. Design and Construction

Product shall be of the design, construction and physical dimensions specified on the applicable product

drawing.

a TE Connectivity Ltd. Company

| Indicates change

*Trademark

For latest revision, visit our website at www.te.com/documents.

For Regional Customer Service, visit our website at www.te.com

1 of 6

TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B

108-1389

3.2. Materials

! Housings:

• Modular jack: Polyphenylene oxide, UL94V-0

• Connector block: Polycarbonate, UL94V-0

! Terminals:

• Modular jack: Phosphor bronze, gold over nickel plating

• Connector block: Phosphor bronze, tin-lead over nickel plating

! Shield: Brass, tin-lead plating

3.3. Ratings

! Voltage: 150 volts alternating current

! Current: 1.5 amperes maximum (signal application only)

! Temperature: -40 to 70°C

! Shielding effectiveness: Shielding effectiveness is measured by comparing level of

electromagnetic emissions from an unshielded system with that of a shielded system. A system

includes active electronic devices and associated cables. Emission levels can be affected by many

variables such as cable type, cable length, grounding method and test setup. Contribution of a

shielded connector to overall shielding will vary with each application. Typically, a shielded modular

plug/jack interface may be expected to improve shielding effectiveness approximately 20 dB as

compared to an unshielded interface.

! Frequency range:

• Category 3: 1 - 16 MHz

• Category 5: 1 - 100 MHz

! Characteristic impedance: 100 ohms

3.4. Performance and Test Description

Product is designed to meet the electrical, mechanical and environmental performance requirements

specified in Figure 1. All tests shall be performed at ambient environmental conditions per Test

Specification 109-1 unless otherwise specified.

3.5. Test Requirements and Procedures Summary

Test Description Requirement Procedure

Examination of product. Meets requirements of product

drawing.

Visual, dimensional and functional

per applicable quality inspection

plan.

ELECTRICAL

Termination resistance, specified

current.

24 AWG wire size;

1 ampere test current;

100 milliohms resistance.

TE Spec 109-25.

Measure potential drop of jack and

mated plug assembly.

Calculate resistance.

See Figure 3.

Termination resistance, dry circuit. 100 milliohms maximum initial.

120 milliohms maximum final.

TE Spec 109-6-1.

Subject jack and mated plug

assembly to 50 mv open circuit at

100 ma.

See Figure 3.

Figure 1 (continued)

Rev B 2 of 6

108-1389

Test Description Requirement Procedure

Dielectric withstanding voltage. 1 kvac dielectric withstanding

voltage.

1 minute hold.

1 milliampere maximum leakage

current. No breakdown or flashover.

TE Spec 109-29-1.

Test between adjacent contacts of

jack and mated plug assembly.

Insulation resistance.

500 megohms minimum final. TE Spec 109-28-3.

Test between adjacent contacts of

jack and mated plug assembly.

MECHANICAL

Sinusoidal vibration. No discontinuities greater than 1

microsecond.

See Note.

TE Spec 109-21-1.

Subject jack and mated plug

assembly to 10 to 55 Hz traversed

in 1 minute at .06 inches total

excursion. 15 minutes in each of 3

mutually perpendicular planes.

Plug retention in jack. Plug shall not dislodge from jack. TE Spec 109-50.

Apply axial load of 20 pounds to

plug housing at rate of .5 inch per

minute with plug mated in jack and

latch engaged.

Mechanical shock. No discontinuities greater than 1

microsecond.

See Note.

TE Spec 109-26-1.

Subject mated jack and plug

assembly to 50 G's half-sine shock

pulses of 11 milliseconds duration.

3 shocks applied along 3 mutually

perpendicular planes, 18 total

shocks.

Mating force. 5 pounds maximum. TE Spec 109-42, Condition A.

Measure force necessary to mate

plug and jack with plug latch

depressed at a rate of .5 inch per

minute.

Unmating force. 5 pounds maximum. TE Spec 109-42, Condition A.

Measure force necessary to

unmate plug and jack with plug

latch depressed at a rate of .5 inch

per minute.

Durability. Termination resistance dry circuit

final.

See Note.

TE Spec 109-27.

Mate and unmate plug and jack for

750 cycles at a maximum rate of

500 cycles per hour with latch

inoperative.

Figure 1 (continued)

Rev B 3 of 6

P1-P3 P4-P6

1-406375-0

Mfr. #:

Buy 1-406375-0

Manufacturer:

TE Connectivity

Description:

Modular Connectors / Ethernet Connectors 110 MJ ASSY, RJ11

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

1-406375-0