SPECIFICATION
65W Constant Current Mode LED Driver
MODEL
OUTPUT
SETUP TIME
Note.4
FREQUENCY RANGE
POWER FACTOR
(Typ.)
EFFICIENCY (Typ.)
AC CURRENT
INPUT
INRUSH CURRENT
(Typ.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
SHORT CIRCUIT
<0.75mA / 277VAC
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 45 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
380.7Khrs min. MIL-HDBK-217F (25 )℃
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.℃
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time or set up failure
5. Aux. 12V will be damaged with short circuit; It will not be available when output voltage is not in constant current region or output no load condition.
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7.The DALI version driver does not support the bit 1: Lamp failure in the Command 144 Query status of the DALI standard.
8. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
0.43Kg; 24pcs/ 11.3Kg/ 0.74CUFT
ENVIRONMENT
SAFETY &
EMC
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
SAFETY STANDARDS
Compliance to EN55015, EN61000-3-2 Class C ( 75% load) ; EN61000-3-3,GB17743,GB17625.1,EAC TP TC 020≧
EMC IMMUNITY
EMC EMISSION
121*77*28.5mm(L*W*H)
UL8750(type”HL”);CSA C22.2 NO.250.13-12; ENEC EN61347-1 & EN61347-2-13 independent, EN62384,
TOTAL HARMONIC DISTORTION
VOLTAGE RANGE Note.3
500ms / 230VAC
47 ~ 63Hz
PF>0.95/230VAC, PF>0.9/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
COLD START 30A(twidth= s measured at 50% Ipeak) at 230VAC100μ;Per NEMA 410
AUXILIARY DC OUTPUT
Note.5
Nominal 12V(deviation 11.4~12.6)@50mA for ODLC-65A only
RATED CURRENT
RATED POWER
CURRENT TOLERANCE
CONSTANT CURRENT REGION
Note.2
OPEN CIRCUIT VOLTAGE
(max.)
CURRENT RIPPLE
±7.0%
5% max. @rated current
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
(Please refer to "STATIC CHARACTERISTIC" section)
180 ~ 295VAC 254 ~ 417VDC
ODLC-65 -700 ODLC-65 -1400
ODLC-65 -1050
ODLC-65 -1750
700mA
1400mA
1050mA
1750mA
65.1W
64.4W
65.1W
63W
69 ~ 93V 34 ~ 46V
46 ~ 62V
27 ~ 36V
118V 60V82V 53V
88% 85%
86%
85%
0.4A/230VAC 0.3A/277VAC
GB19510.1,GB19510.14; EAC TP TC 004, IP67 approved
Hiccup mode,auto-recovery after fault condition is removed for DA type；
Hiccup mode,re-power on to recovery for other type
THD< 20%(@load 75%/230VAC,277VAC)≧
(Please refer to “TOTAL HARMONIC DISTORTION” section)
Tcase=-20 ~ +85 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃
MAX. CASE TEMP.
Tcase=+85℃
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( ),EAC TP TC 020surge immunity:Line-Line:1KV
ODLC-65 series
NO LOAD / STANDBY
POWER CONSUMPTION
Standby power consumption <0.5W for DA-Type
No load power consumption <0.5W for Blank-Type, <1.2W for ODLC-65A
DALI STANDARDS Note.7
Compliance to IEC62386-101,102 for DA-Type only
File Name:ODLC-65-SPEC 2018-01-15
